What is the most reliable source to get Impact factor of journals?

Source to get Impact factor of journals

01 March 2021 6,654 2 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

Why initial concentration of Pb not the same as calculated one when testing using AAS?

I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...

26 February 2021 9,580 4 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

Best FE Program for Concrete Strengthened with FRP Sheets?

Colleagues, I have been using ANSYS to model concrete strengthened FRP sheets, but less than happy with it. Any has recommendation for efficient, easy to use FE program for modelling concrete...

22 February 2021 7,528 3 View

Any information about dinitrosalisylic acid reagent end point color stability ?

I work on estimation of alpha amylase activity using dinitrosalisylic acid reagent If i put the reagent to stope the enzymatic reaction and allow the reagent to react with the produced reducing...

17 February 2021 7,402 4 View

Using liquids as superstrate in Fabry-Perot Cavity Antenna?

Hi, A Fabry Perot Cavity allows to increase the directivity of a low gain antenna by putting in the top of cavity a superstrate with high permittivity such as a ceramic (er=10.2). However,...

09 February 2021 6,799 8 View

Experiment statistical analysis?

07 February 2021 3,635 3 View

Distribution of modes fields ?

Hi, We find a specific distribution of electric fields in structure for different frequencies which can be seen using em solvers and known as modes. I would like to know how we can choose the...

04 February 2021 10,043 3 View

Greetings Doctors, If i did a same experiment for a 2 populations and i need to publish this work in a 2 different papers?

If i did a same experiment for a 2 populations and i need to publish this work in a 2 different papers can i use the same word in the writing of these 2 papers or this would considered as...

04 February 2021 4,648 4 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

Has anyone succeeded in capturing uranium atoms in a fullerene structure?

Additional questions are: What are the encapsulating atoms? How difficult was the process and what rates were achieved? What factors most seriously affect the economics?

20 February 2021 3,134 5 View

What type of pressure sensor are usually used in microfluidics?

My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...

18 February 2021 9,928 2 View

Is it better to push or pull liquid through microfluidics with a syringe pump?

I have a PDMS microfluidic device that I want to perfuse cells through (there are also adherent cells in the channels). Is there any difference if I use a syringe pump to push the cells through...

30 January 2021 4,092 3 View

Silane solution and application to Glass ?

30 January 2021 7,924 3 View

Suggestions for using antisense oligonucleotide for brain delivery?

hello I am working on a project that includes gene delivery to the brain. my intentions are encapsulating a gene in a Chitosan NP and IV administration the NP to rats. beside plasmids is there...

29 January 2021 4,455 5 View

Is there a protocol for the insulin encapsulation at physiological pH?

Hello everyone, I am going to start my master thesis on the encapsulation of insulin. In almost all protocols we found an acidic pH is necessary. Unfortunately, pH

27 January 2021 3,692 5 View

how to add blood and plasma in comsol?

I am trying to model separation of the plasma from the blood on a rotating microfluidic platform. I am not able to add blood and plasma in Comsol. someone please provide me your valuable...

27 January 2021 8,263 1 View

Any stable dye to color acrylamide hydrogel beads?

Hi! We are generating hydrogel beads(50-60um) using microfluidics as single-cell beads. To simply all the experiments (especially the centrifuge), I am looking for a dye. The dye should be stable...

14 January 2021 4,383 8 View

How to interface Semi conductor physics and Fluid flow physics in COMSOL?. What are the parameters to be considered while we interface them?

I am using a silicon nano wire in microfluidic channel to identify the some changes in parameters like voltage and current. but i am unable to interface them. the two physics run individually but...

10 January 2021 8,894 1 View