What are steps to for piezoresistive cantilever(composite layer) for change in resistance Vs Applied force and Deflection VS applied force?

06 June 2018 0 2K Report

any experts in comsol simulation please give required steps for design of composite layer cantilever and plots between Deflection Vs force and chnage in resistance Vs applied force

Badges
Science topic

More Vasu Babu's questions See All

How to use parasitic heating heat transfer module in COMSOL 5.0?

please give me answer any expert i want analyze a stress by applying parasitic heating by heat transfer module in Comsol 5.0v. and give me process steps to analyse change in resistance by in...

31 December 2018 4,441 0 View

How to use a parasitic heating in heat transfer module in comsol multiphysics. now iam using cosol.0?

please give answer any expert and i want design a piezoresistive cantilever with parasitic heating create a stress and on top layer and finally i want to analyze the deflection in cpomsol r5.0...

31 December 2018 5,560 0 View

What are the methods for electrical conductivity measurements for nano particles?

what are the methods used for conductivity measurement of nano particles?

05 June 2018 930 8 View

Comsol experts please give me clarity about cantilever design and frequency ,phase angle, amplitide measurement in comsol software?

i want to design and analysis of PZR cantilever with frequency,amplitude and phase angle measurement in comsol multiphysics 5.0V

05 June 2018 6,524 0 View

How to measure change in resistance of a thin film?

please give me suggetion

31 December 2017 4,071 6 View

How to find out resonant frequency and natural frequency in comsol

any body please give me suggestion to find out resonant frequency and natural frequency in comsol

01 January 1970 7,127 3 View

How to detect a ammonia gas with polyaniline thin film ?

Hi, any one give me procedure for ammonia gas sensing with polyaniline thin film by four point probe

01 January 1970 5,396 3 View

Experimental set up for ammonia gas sensing with polyaniline thin film by four point proe.

please give the procedure for ammonia gas sensing with polyaniline thin film by four point probe.

01 January 1970 4,751 2 View

What is your perception on using visual analysis or quantitative approaches to evaluate data from single-case research designs (n of 1 trials)?

Results of single-case research designs (i.e., n-of-1 trials) are often evaluated by visually inspecting the time-series graph and computing quantitative indices. A question our research team is...

03 March 2021 687 1 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

How to approach CFD simulation results of a flow past a cylinder?

Hi all, I'm doing a transient simulation of flow past a rectangular cylinder close to the free surface. As far as I'm concerned, the common practice is to discard the initial stages of the...

25 February 2021 1,348 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View