How to use parasitic heating heat transfer module in COMSOL 5.0?

01 January 2019 0 4K Report

please give me answer any expert i want analyze a stress by applying parasitic heating by heat transfer module in Comsol 5.0v. and give me process steps to analyse change in resistance by in piezoresistive cantilever by applying a parasitic heating with heat transfer module.

Badges
Science topic

More Vasu Babu's questions See All

How to use a parasitic heating in heat transfer module in comsol multiphysics. now iam using cosol.0?

please give answer any expert and i want design a piezoresistive cantilever with parasitic heating create a stress and on top layer and finally i want to analyze the deflection in cpomsol r5.0...

31 December 2018 5,560 0 View

What are steps to for piezoresistive cantilever(composite layer) for change in resistance Vs Applied force and Deflection VS applied force?

any experts in comsol simulation please give required steps for design of composite layer cantilever and plots between Deflection Vs force and chnage in resistance Vs applied force

05 June 2018 2,121 0 View

What are the methods for electrical conductivity measurements for nano particles?

what are the methods used for conductivity measurement of nano particles?

05 June 2018 930 8 View

Comsol experts please give me clarity about cantilever design and frequency ,phase angle, amplitide measurement in comsol software?

i want to design and analysis of PZR cantilever with frequency,amplitude and phase angle measurement in comsol multiphysics 5.0V

05 June 2018 6,524 0 View

How to measure change in resistance of a thin film?

please give me suggetion

31 December 2017 4,071 6 View

How to find out resonant frequency and natural frequency in comsol

any body please give me suggestion to find out resonant frequency and natural frequency in comsol

01 January 1970 7,127 3 View

How to detect a ammonia gas with polyaniline thin film ?

Hi, any one give me procedure for ammonia gas sensing with polyaniline thin film by four point probe

01 January 1970 5,396 3 View

Experimental set up for ammonia gas sensing with polyaniline thin film by four point proe.

please give the procedure for ammonia gas sensing with polyaniline thin film by four point probe.

01 January 1970 4,751 2 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View