What are statistical models that parametrize mathematical models of growth of gas bubbles in tissues undergoing decompression?

04 April 2016 0 10K Report

Badges
Science topic

More Khaled G. Mohamed's questions See All

Need ISI journal impact factor list 2017?

Need ISI journal impact factor list 2017, see the attached file. Regards

05 June 2018 6,480 0 View

Should you explain the existence of fishes and other sea creatures in closed lakes?

Dear Colleagues, Should you explain the existence of fishes and other sea creatures in closed lakes that don't connect to any river, sea or ocean. The resource of these lakes is only sky rains?...

06 July 2017 4,591 1 View

Are there any measured data for viscosity of blood or other tissue fluids in vivo or in vitro?

Dear colleagues, Best greetings and my best wishes for happy times for you. Are there any measured data for viscosity of blood or other tissue fluids in vivo or in vitro? Thanks in...

06 July 2017 8,986 0 View

Need ISI impact factor list for scientific journals 2017 release?

It 's attached in pdf and xlsx formats. Regards, Khaled

05 June 2017 7,788 4 View

Why some kinds of insects are attracted to people who have yellow-colored dresses?

01 February 2017 2,352 0 View

What are newer teaching strategies?

Dear colleagues, What are newer teaching strategies, specially for undergraduate level, and mathematics subjects? Thanks in advance for your contribution.

09 October 2016 8,465 4 View

Dear colleagues, What is your opinion about "flipped classroom" as a modern teaching strategy?

Flipped classroom is an instructional strategy and a type of blended learning that reverses the traditional learning environment by delivering instructional content, often online, outside of the...

08 September 2016 6,286 7 View

How can a researcher do a good statistical analysis for a problem?

Dear specialists, How can a researcher do a good statistical analysis for a problem?

08 September 2016 5,570 4 View

Who first invent the simple mathematical symbols like +, -, = ... etc?

"Mathematics is a language of symbols". Do you know: Who first invent the simple mathematical symbols like +, -, = ... etc?

07 August 2016 1,872 4 View

About recognition of ethnic group of a person?

Is there any technique or Image processing software to determine the original Ethnic group of a person via his photograph?

07 August 2016 5,747 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

"A Markov-like Model for Patient Progression"?

A Markov-like Model for Patient Progression" Markov Chain Monte Carlo (MCMC) Markov Chain Monte Carlo (MCMC) is a powerful computational technique used to draw samples from a probability...

05 August 2024 10,079 0 View

If we are using snowball sampling technique, how do we justify the true representativeness of the sample statistically? is there any statistical test?

Are there any statistical methods to justify your sampling technique using SPSS or AMOS?

05 August 2024 9,153 4 View