What are ideal Grid Parameters R, L and C?

01 January 1970 1 3K Report

While working on a grid connected inverter interface, I am modelling a purely resistive grid in simulation model. How right or wrong am I in doing so. In either case please indicate as to what value of R, L or C should I use?

Severin Nowak

I recommend to have a look at this text book on modelling voltage source converters: https://ieeexplore.ieee.org/book/6739364

Badges
Science topic

Similar topics
Engineering
Modeling

More Atul Viswas's questions See All

What is Impact Factor (RJIF)?

Hi, Can some scholar explain Impact factor RJIF? How this is different from Scopus rating? A journal claims Impact Factor (RJIF): 8.4. How to interpret this number? Please advise.

10 May 2024 9,073 2 View

Should overrepresented sequences be retained or trimmed in small RNA sequencing data?

In small RNA sequencing data analysis, I have encountered overrepresented sequences. When processing such data, should overrepresented sequences be retained or trimmed? What are the potential...

10 March 2024 468 2 View

Under which Category a peer reviewed unpublished paper can be uploaded?

I submitted a draft paper for publication around early 2021. The paper was not cleared on technical grounds & thus not published. Later, I submitted an updated draft to the Editor in his personal...

18 January 2024 7,357 2 View

Does Acetyl Chloride (AcCl) is best alternative for acetic anhydride for acetylation reaction?

04 January 2024 3,573 1 View

How to numerically model Pool boilng Heat Transfer phenomena during quenching ?

Dear Genius Researchers, I would like your guidance if anyone can help me in model (Numerically) pool boiling heat transfer phenomena. I am working on Mathematical modeling of "Quenching...

19 October 2023 2,935 2 View

Is using nichrome or Kanthal heating element in noble gas (ARGON)?

Hello all, I am conducting a experiment where I need to heat up argon. I understand from publicly available resource that Nichrome or Kanthal heating elements protect themself by producing a...

11 October 2023 8,220 1 View

Protocol for activation and estimation of phospho zap70 in mouse spleen or whole blood by ELISA?

HI, We have tried invivo stimulation phospho zap70 in mouse with the intraperitoneal administration of mouse CD3 antibody using 700ng and 10 ug. 10 and 30 after CD3 administration, we collect the...

20 August 2023 3,035 3 View

Protocol for activation and estimation of phospho zap70 in mouse spleen or whole blood by ELISA?

HI, We have tried invivo stimulation phospho zap70 in mouse with the intraperitoneal administration of mouse CD3 antibody using 700ng and 10 ug. 10 and 30 after CD3 administration, we collect the...

18 August 2023 5,146 0 View

What are the right standard (standard 1 & 2) values of Qubit RNA BR quanitification, so as to accurately quanity RNA samples ?

Before the quantification of RNA samples, I ran the standards twice and observed two different readings. 1st observations: Std 1 = 212.07 & Std 2 = 2278.50. 2nd observations: Std 1 = 149.24...

19 July 2023 8,572 1 View

What is the most effective mixer for powders of different sizes and density?

I need to mix 16 powders of of dissimilar sizes and density in batch sizes of 2-6 Kg. These powders are usually of 20-50 microns in size. I understand there are different types of machine that use...

10 June 2023 9,455 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Smart grid ideas?

How to use and this is economical?

06 August 2024 3,160 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How can major oxides determined by ICP-MS/ES be normalized to 100% volatile free? How does this connect with LOI?

I am analyzing cherts from different sources found within one specific geologic formation using ICP-MS/ES. My committee was asking this question about my analysis. I was not sure how to answer this

05 August 2024 7,902 3 View