I need to cure large number of PDMS based samples for the fabrication of piezoresistive sensors. But I do not have hot air oven for this purpose. What are the other option to cure PDMS other then keeping it at room temperature for 48 hours?
An alternative to an oven could be to use a hot plate. Depending on the film thickness you will need more or less time. For me worked perfectly!
A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...
11 August 2024 9,801 2 View
I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...
07 August 2024 5,177 3 View
Hey All! I am wondering what might be wrong with my band structure. I did the calculations using VASP and plotted the results using Origin. Although I have tried changing various input...
25 July 2024 2,920 11 View
Gene sequencing related trouble shooting
25 July 2024 4,149 2 View
I am looking for a lipid waste disposal method, keeping in mind the environmental, health and safety aspect of lipid waste. Could someone please provide guidelines or the lowest acceptable...
25 July 2024 637 5 View
I am writing a paper as a part of my course. I am new in London and was wondering that what publications should look upto?
21 July 2024 3,538 1 View
After World War, we have seen the formation of the United Nations. The sovereign body for peacekeeping but with regards to the Russia-Ukraine war it is visible that the UN seems to be ineffective...
18 July 2024 4,674 4 View
It has been a quite long time since the Russia and Ukraine war has been going on and if we see the context of Geopolitics and International Relations we don't see a mediation between the two...
18 July 2024 6,737 4 View
One of the papers I read by Toby, where (title of the paper was "R factors in Rietveld analysis: How good is good enough?"), he tells us that to get good chi square value, you must have low Rwp,...
17 July 2024 9,668 4 View
Please help me in plotting the photon-magnon coupling plot as shown below
14 July 2024 1,632 1 View
My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...
07 August 2024 4,600 2 View
Air moisture harvesting Air water collection devices
06 August 2024 5,473 2 View
need of sensor details or sensor development for this question.
28 July 2024 4,539 3 View
please suggest the research paper related to the instrument is used in it.
16 July 2024 8,453 1 View
I try to understand the ESP mechanism working. What kind of sensors it has, Is it necessary to modify or boost its mechanical ?
15 July 2024 4,772 1 View
Continuous glucose monitors (CGMs) help patients and doctors make more timely management decisions by monitoring blood glucose levels in real time. An insulin pump provides continuous insulin...
07 July 2024 7,742 0 View
I use PDMS to build a microfluidic system, but it is not hardening at all, although I use TEOS as a cross-linker and also ATPES in a ratio of 1:10, and it's been 3 days at 80 degrees of 3 ml cast...
01 July 2024 604 3 View
no
01 July 2024 8,134 3 View
1- Please provide information about the chemical composition of curing agent for PDMS(Sylgard 184 Kit)? 2- what dry solid percentage is obtained for a ratio of 10 to 1(PDMS to hardener)?
30 June 2024 6,814 2 View
I have calculated CDI (inhalation) of Ozone, CO, SO2, NO2, NO, and TSP (total suspended particulate matter) . However I cannot find RfC (Reference concentration) or even NOAEL of any of these...
27 June 2024 4,488 0 View