Warning message from Simulink/Simpowersystem?

Tony Castillo-Calzadilla @Tony_Castillo-Calzadilla

03 March 2016 0 7K Report

Does anybody the solution for this warning message in one simulation?:

Warning: Matrix is close to singular or badly scaled. Results may be inaccurate. RCOND = 1.938401e-16.

Badges
Science topic

More Tony Castillo-Calzadilla's questions See All

Why battery always retain the same value of power?

Dear all, I have been testing a model that is in the Matlab library (https://es.mathworks.com/help/physmod/sps/ug/simplified-model-of-a-small-scale-micro-grid.html), this is named "power...

10 November 2020 2,117 3 View

How to desing a simplified DC-DC Converter?

I request your help for modelling a simplied DC-DC converter, I already have a detailed model, but in this moment I just want to speed up the simulation time making it shorter, that is why I ask...

02 March 2019 7,232 6 View

Speed up the performance in DC-DC Power Converter?

Dear Ms, I have been thinking in how to Speed up the performance in DC-DC Power Converter?, because I have a systems which has 2 DC-DC converters, the first one is working in order to obtaing the...

30 January 2019 4,819 7 View

How to calculate the cost of building and maintain a grid-connected microgrid?

Dear Ms, I am seeking papers or official reports, in order to find, how do the plannifier determine and forecast the cost of implementing a microgrid?. Do you have information about it?, because I...

16 December 2018 153 1 View

How to calculate the cost of building and maintain a grid-connected microgrid?

Dear Ms, I am seeking papers or official reports, in order to find, how do the plannifier determine and forecast the cost of implementing a microgrid?. Do you have information about it?, because I...

11 December 2018 2,375 1 View

How to connect a power DC-DC converter to a PV system under partial shaded effect?

Hi Ms all, I need some help in order to understand better some issues that I am experiencing in my PV systems under partial shaded effect. The issues that I need to overcome in my experimentation...

09 October 2018 6,987 2 View

How to connect MPPT converter with the PV panels under partial shading to?

Dear all, I am working on modelling a microgrid under different shading patterns (shown on attached figure), but I have a doubt about the modelling measures. My doubt is due I have three I_PV and...

02 March 2018 5,513 5 View

No title

In a Solar System, how can I obtain the MPP of solar cells meanwhile I control the output voltage and I set it in 24 V DC?. My main issue is that my converters is configured to work in the MPP and...

31 December 2017 3,431 7 View

Could anyone tell me or give material about which is the maimum voltage to charge a Solar Batery made of Li-ion?

Hello my dear colleagues, I'd like to find informatior or expertice, about what is the maximum value of Voltage that I should apply between terminals in oder to proceed to charge or recharge the...

11 December 2017 9,872 5 View

How can I modelize the power losses produced by cabling resistance in a Model based into the library Simscape Power System of Simulink ?

Hi everybody here, Researchers community could anyone tell me how to mimic the cabling resistance in a model made in the environment SPS?. I am trying to do it so as to represent and measure the...

10 November 2017 3,237 2 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View