09 September 2018 0 5K Report

Dear all,

I want to know about the wall lift off in CFD simulations

What's it's significance and why they are different in FEM and FVM?

Moreover, if it only depends on meaning, then why in particularly Comsol , it gets calculated after full simulation?

Please let me know about it.

Thank you

More Parag Patil's questions See All
How to vary thickness of surface unevenly in comsol geometry?

I have a tube with a fixed inside thickness. Now, I want to change thickness of some part of this tube to X mm and some part to Y mm. Rest of the part has no change. Moreover, the parts of...

02 March 2019 7,711 3 View

Are oscillations in COMSOL Water-Hammer example die down with respect to time ?

I recently saw an example of water-hammering effect example of COMSOL Multiphysics. The example shows that the sudden closing of a valve produces pressure-shock through out the pipe upstream to...

31 December 2018 1,411 3 View

Shell and tube heat exchanger in comsol is not converging ?

I'm simulating a shell and tube heat exchanger in comsol . I am plugging some of the tubes within the structure to see its effect on del.P and temperature. When I plug 18 of 19 tubes, and one...

09 October 2018 9,825 4 View

Related to the MATLAB-Livelink functionality ?

I have a doubt: A : 1. If a parameter value (say 'x = 100 ') is changed in model via Matlab-Livelink (via Matlab coding) 2. model is run. After it, B : 1. Again the paramater value is changed...

07 August 2018 6,347 0 View

CFD and Aspen Plus Validation of Heat Exchanger ?

I have simulated a heat-exchanger in COMSOL. The same heat-exchanger is simulated (with the exact geometry ) in Aspen Plus. I'm facing following problems in above: 1. The results of Aspen Plus...

06 July 2018 6,033 0 View

Time Constant for a heat exchanger ?

I have a shell and tube heat exchanger (1-1 pass ). It has shell of 250 mm ID and tubes of 50 mm ID (# 19). Length is 500 mm. I want to know the time-constant for this heat-exchanger (approx....

05 June 2018 1,172 0 View

External material addition in COMSOL ?

Hello, I want to add an external material to the COMSOL for simulation. How can we do it? thanks.

04 May 2018 4,035 0 View

Using global variable in S-function ?

Dear all, I am trying to connect a function-file in MATLAB to Simulink via 2nd level S-function. But I have a global variable defined in my function file. Can anyone let me know, how to declare...

03 April 2018 1,345 3 View

Connecting COMSOL to Simulink ?

Dear all, I want to use the S-function in Simulink to connect it to COMSOL. I am able to use the Livelink and can import COMSOL model to MATLAB and can access the results. But my problem is as...

03 April 2018 9,674 1 View

Co-Simulating Aspen Plus / Hysys and CFD/COMSOL or FLUENT using CAPE-OPEN?

Dear all, I am trying to co-simulate a chemical process in two-different environment. One is Aspen Plus and another is an CFD based simulator. The process has different units to be simulated in...

02 March 2018 4,485 4 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close