UM option for RBE3 elements in NASTRAN?

03 March 2016 1 4K Report

Can someone explain the proper usage of UM option with an example for RBE3 element. Various applications where it can be used.

Paul Thomas

Hello Amique Ukani,

I am trying to figure out the proper usage for um option in RBE3. Have you find any documents which helps to understand this concept?

Thank you,

Paul Thomas

Badges
Science topic

More Amique Ukani's questions See All

Fatal error while performing Topology Optimization in Nastran?

Following is a snippet of the error from .F06 file. *** USER INFORMATION MESSAGE 9051 (SUBDMAP FEA) STATIC SENSITIVITY ANALYSIS INITIATED. DESIGN CYCLE NUMBER= 1 *** USER INFORMATION...

09 October 2018 5,309 4 View

How to formulate a Structural Topology Optimization problem in MSC Nastran?

I am trying to optimize a circular casing structure for reducing the von-mises stress on it. Many examples of such problems have Minimizing compliance as the objective with mass fraction and/or...

09 October 2018 8,007 12 View

Simulation of an Anti-roll bar in FEM NASTRAN?

I am trying to simulate the Anti-roll bar mechanism in Nastran. I have got good results so far, meaning torque in the bar under rolling and no torque when leveled. During this the bushings of the...

11 December 2017 5,343 2 View

What is the difference between DSTRAN and DFGRD1 in Abaqus UMAT?

I want to know what exactly both these variables convey. How they differ from each other. How can I get DSTRAN from DFGRD Explanation with an example will be much useful.

04 May 2015 6,037 1 View

What is DSTRAN and STRAN variable in the Abaqus UMAT (user material) when Thermal expansion is not included in the Material definition?

According to the User subroutine Abaqus manual, "If thermal expansion is included in the same material definition, the strains passed into UMAT are the mechanical strains only (that is, the...

03 April 2015 7,329 7 View

Is anyone familiar with rotation of STATE variables in UMAT?

The STATEV that get stored at the end of the iteration are getting carried forward. But after rotating by DROT, I printed to see the value of STATEV. They become zero after rotation. I have used...

03 April 2015 9,439 4 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View