Hello Everyone ,
Hope you are doing well. I have to rotate a 3D wing at different roll angles with the help of udf in Ansys fluent. Can someone provide me literature regarding this .
Regards ,
Aamir
Hello Aamir Sultan,
You can use DEFINE_CG_MOTION (name, dt, vel, omega, time, dtime) and define its angular velocity with time. Examples can be found in ANSYS Help.
Best.
Wenzhao Chen , Emre Kara Thank you so much for your kind input.
Hello Everyone ! I have been having this question in mind for quite a long time that we have this huge amount of data available in the form of wind tunnel experiments , in-flight data and...
31 December 2019 2,197 8 View
Hello Everyone , I was wondering is there any literature available on the extent of transitional regime in space and that for how long does it last ? Regards Aamir Sultan
31 December 2019 1,415 3 View
Does continuity , momentum and energy laws remain conserved when we use local refinement in adaptive meshes ?
31 December 2019 4,180 4 View
Hello Everyone , Pressure far-field boundary condition is often recommended for flows with varying density , but why does it require so larger outer domains. Regards Aamir Sultan
31 December 2019 3,252 3 View
Hello Everyone ! It is alway said that SA model is apporopriate for adverse pressure gradients then how come it lacks the ability to accurately predict separation ?
11 December 2019 559 2 View
Hello Everyone I am simulating an airfoil at Low Reynolds Number flow Regime Re=10^5 , in this particular case a laminar boundary layer separates , forming a laminar separation bubble , then...
11 December 2019 3,886 3 View
Hello Everyone , Hope you are doing fine . I have this question about the reference values , that which length should one use while doing external aerodynamic CFD simulation of a full aircraft...
10 November 2019 5,333 4 View
Hello Everyone , Hope you are doing fine . I was going through this paper of P. Cosyn and J. Vierendeels on ''Numerical Investigation of Low-Aspect-Ratio Wings at Low Reynolds Numbers'' in which...
08 September 2019 1,663 2 View
Hello Everyone , I am doing a 3D simulation of a 3D wing at a Reynold's number of 10^5 and a mach number of 0.02 . When I use pressure based solver my solution diverges within few iterations ....
02 March 2019 5,514 2 View
Hello Everyone ; Hope you are doing great . I have to change the axis of rotation from default setting i,e z-axis to x-axis in the given UDF ? How can I do that ?...
01 February 2019 9,641 4 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...
10 August 2024 3,629 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
Request Python code from this article : Gender equity of authorship in pulmonary medicine over the past decade. THANKS!
08 August 2024 6,242 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Visual Studio Code (VS Code) has become a popular choice among developers for several reasons: 1. **Free and Open Source**: VS Code is free to use and open source, making it accessible to...
07 August 2024 7,013 4 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View