To model the Atmospheric Plasma Spray (APS) in atmosphere by ANSYS Fluent software, is it necessary to simulate NOx reactions?

More Mahrukh Mahrukh's questions See All

Which statistical analysis model to use to calculate the relationship between diabetes incidence and endothelial function?

I have longitudinal data with 2 follow ups at year 1 and 3. At baseline we have measure of endothelial function and we want to calculate the relation ship between endothelial function and diabetes...

23 June 2019 7,691 6 View

Is there any matlab command for pole placement for descriptor systems?

I am designing a feedback tracking controller for descriptor systems.does there exist any command in matlab for pole placement of descriptor systems or not(as in case of satespace system "place"...

02 December 2018 6,207 1 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

Frank Collins

I have no experience with these fields so cannot provide an answer.

Anmol Taploo

It would not make much difference, your main species that would give drastic variations in your readings will be N2, O2, humidity etc.

I hace no experience with fluent or with modeling plasmas. Each problem is different and must be explored alone. Fore example, what are the number densities, relevant cross sections and rate equations with the other species known to be present. Sorry I cannot be of more help.