Thermoplastic Polyimide or any other hot-melt Adhesive for Bonding ?

08 August 2016 0 2K Report

Thermoplastic Polyimide or any other hot-melt Adhesive with Tm over 180-200C for Bonding Thermally Resistant Materials

Badges
Science topic

Similar topics
Entomology
Resistance

More Leonid V Vladimirov's questions See All

Binder for reinforced plastics with fluidity temperature 100-120C, prepreg on its base containing >50% carbon filaments and examples of articles made?

Binder for reinforced plastics with fluidity temperature 100-120C, prepreg on its base containing >50% carbon filaments and examples of articles made of it. We seek for prepregs with at least...

07 August 2018 1,232 0 View

Adhesive for carbon and/or glass filaments sustaining -150C + 150C?

We need Adhesive for carbon and/or glass filaments sustaining -150C + 150C? It may be like PolyAmide Imide adhesive or adhesive cured by UV, or any combination of adhesives.

07 August 2018 3,057 5 View

Polyimide based on Diamine R?

Polyimide based on Diamine R? for preparation of thermal-resistant Polyimide powder

05 June 2018 871 2 View

What is more important than success in our Living?

My previous question was: """To be successful in life - what does it mean?""" Almost all the answers to this question were about: "What is the Success? and how to reach the success" - a...

03 April 2018 2,187 96 View

How to remove from the Metal surface the PSA adhesive?

How to remove from the Metal surface the PSA adhesive by using non-aggressive solvents? What type of solvents would you recommend? at what temperature?

03 April 2018 5,711 6 View

What are the best solvents to precipitate Aromatic PolyAmic Acid from its solution in DMF or DMAC?

31 December 2017 4,755 2 View

How to obtain a precipitated powder of Poly-Amic Acid based on aromatic diamine and aromatic dianhydride?

How to obtain a precipitated powder of Poly-Amic Acid (PAA) based on aromatic diamine and aromatic dianhydride? It is well known that for several Aromatic Polyimides (PIs) in the course of...

11 December 2017 2,284 2 View

Band assignments for FTIR spectra of Ground Rubber Tire Crumps?

FTIR spectra of GRT are difficult to "read" because of carbon filler. The bands are broad and have of very low intensity. As a whole the contribution of the spectrum of GRT to the total spectrum...

09 October 2017 7,108 6 View

Thermo-resistant Rubber for Gumming Calender Shaft?

We are looking for manufacturer/supplier of Super-Thermo-Resistant Rubber for Gumming Calender Clamping Shaft. We'd greatly appreciate an advice concernig: type of Rubber and Suppliers.?

09 October 2017 2,355 0 View

What plasticizers could you recommend for Cellophane film?

What plasticizers could you recommend for Cellophane. How to plasticize Cellophane - at some stage of film manufacturing ? or via swelling ?

07 August 2017 1,550 5 View

Should I include H atom into C3N5 when i am doing DFT modelling?

Hi all, my experimental XPS results shown that my C3N5 sample consists of N-H bond, hence in this case I should incorporate the N-H bond into my DFT modelling. However, I do notice several papers...

07 August 2024 8,414 2 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

Expansion thermal of muscle ?

What is the thermal expansion coefficient of human muscle?

27 July 2024 7,190 0 View

What is the best way to drop a plasmid?

Please address the best way to drop a plasmid. Background: I have a "bait" plasmid resistant to kanamycin and a "prey" plasmid resistant to carbenicillin. After many rounds of streaking on...

25 July 2024 2,532 3 View

What is the principle/mechanism behind aging of carbon (graphite) containing refractory mix for isostatically pressed refractories?

The resin bonded carbon containing refractories are aged before use. How time of aging is determined? And mechanism behind aging.

23 July 2024 3,205 0 View

Is it possible to manufacture polypropylene sheets using a biaxial process?

I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...

21 July 2024 1,559 1 View

Can Langmuir constant related to bonding energy (Kl) and Freundlich exponent (1/n) indicative of ads intensity show opposite trends with temperature?

The adsorbate is Arsenic and the adsorbent is a soil

18 July 2024 332 8 View

How to create parameter and coordinate files for ligand in amber when FATAL error (maybe due to duplicate bond specifications) happens?

Hello, I'm trying to create parameter and coordinate files for a drug (PRG-A01) found on the following page: http://www.probechem.com/products_PRG-A01.html I used the guide made by Michael...

17 July 2024 3,472 3 View

Kraft lignin and MMA(Methyl meth acrylate) free radical polymerization for synthesis of thermoplastics?

I am conducting free radical polymerization using Kraft lignin and MMA, with DMSO serving as the solvent and there is also an initiator. Following the reaction, I obtain a solution, but I am...

15 July 2024 9,827 1 View

How can I extract glycosides from mangrove leaf samples without an incubator that can reach temperatures above 60°C?

I want to extract glycosides from my mangrove leaf samples, but my laboratory lacks an incubator capable of reaching temperatures above 60°C. The paper I am following specifies a minimum...

13 July 2024 3,686 0 View