Synchronous reluctance motor in COMSOL?

15 February 2021 0 7K Report

Hello!

Could you tell me what the error is in the model?

I set the rotating part as a rigid body with an applied torque created by the engine itself (that is, idle), but for some reason it is not synchronized in speed with the frequency of the supply voltage. A three-phase system of 1050 Hertz is connected, the engine rotation speed is 31500 rpm, but it does not reach this speed

Badges
Science topic

More Maksim Sitnikov's questions See All

How to achieve the convergence of the solution in COMSOL Multiphysics?

Hello! Please tell me how to achieve the convergence of the solution ... In Newton's method I set 50 iterations and the finest grid, but the solution still does not converge I would be grateful...

23 January 2021 935 5 View

How to set up a PI controller for a wind turbine pitch angle control system?

Hello dear colleagues and experts! When developing a model of a wind generator, I faced the problem of adjusting the PI controller for the pitch angle. I read a lot of articles, but the PI...

27 October 2020 9,339 10 View

What is the meaning of an adjustment for confounding factors in the context of multiple regression analysis and epidemiology?

I have reformulated the question I mean a statistical approach for adjusting values using multiple linear regression which is often used in ecological studies (e.g. Urashima et al., 2020 Int J...

13 October 2020 3,142 5 View

ADP-Glo test for ATPase activity of NLRP3?

Hello colleagues! I want to investigate the atphase activity of nlrp3 in the ADP-glo test. but I don't know what type of buffer to use for analysis. Can anyone help me?

12 September 2020 7,596 3 View

Analysis of Neural Data?

I would like to know what are good sources (books, tutorials, references in general) for the application of Data Science to the field of Neuroscience (Analysis of Neural Data), and where could we...

04 August 2020 5,848 4 View

Is comparing some rates among the patients with respective rates in general population appropriate in epidemiology?

Is it appropriate to compare rates of (for instance) tea consumers among patients admitted to a hospital with some disease, with rates of tea consumers in general population in the same country?...

11 March 2020 5,560 3 View

What is the difference between "exact polarizability" values and values beginning with "Polar" in the end of output Gaussian file? And which units?

Gaussian output contains a string "exact polarizability" with some values and also there are some values beginning with "Polar"in the end of the output? They have different values. What is the...

13 November 2018 3,646 3 View

Hello! Can anyone please explain the difference between static and dynamic hyper(polarizabilities)?

I'm trying to perform NLO properties calculations with Gaussian and I need to calculate first hyperpolarizability. I faced in literature with static and dynamic ones. Can anyone explain the main...

12 November 2018 1,699 4 View

Could you advice a software for DNA sequence annotation in printed materials?

Sometimes you have to represent a nucleic acid sequence on paper, not as an image, but as a text with notes. Is there any suitable program (Windows OS) possible to divide raw sequence into pieces...

24 September 2018 1,939 2 View

Question regarding the representation of the E(X*X^T) matrix of a random vector with a non-negative support?

There is a random vector x=(x_1,x_2,...,x_n) with a non-negative support. There is additional constraint Ax=b. Is it true that E(x*x^T) belongs to the set conv{yy^T

30 May 2017 4,647 7 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Trouble with Charting with Google Earth Engine (Technical)?

Hello. I have a problem with the charting in google earth engine. I created an image collection by combining 5 image collections of five parameters and using ee.Join.inner ( ) and .apply ( )...

26 February 2021 7,084 2 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

How can we limit artifacts caused by rotation in fiber photometry?

We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...

25 February 2021 568 1 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View