Mfznfe5-c

What does the symbol MFZnFe5-C for finish plating means?

05 June 2013 6,317 4 View

To load CSV file using VB 2010

Csv file consists of x, y, z (three colums). I have to load those three colums values into matrix & then i have to plot x vs y, x vs z. x y z 1 11 13 2 8 45 3 13 18 4...

11 December 2012 5,777 2 View

Fluid Flow Control

Is it possible to suck air naturally inside a chamber in a vehicle through a duct? the duct to send controlled pressure of air inside the chamber for varying speed naturally without using any...

10 November 2012 9,233 5 View

FeMap Nx NASTRAN, Ansys, Abaqus, HyperWorks

Idea of learning a analysis software.. Which among the four is best with respect to application, popularity, useage and user friendly? I learnt Ansys structural and thermal analysis but yet to...

09 October 2012 5,539 9 View

Can anyone clarify fluid Conduction?

I came across liquid and gas conduction in heat transfer when I was reading about conduction. Conduction normally refers to transfer of heat taking place in one or more solids that are in contact....

09 October 2012 381 11 View

Plane Stress Plane Strain

Can anyone brief me with example about the plane stress, plane strain conditions? I know that in plane stress condition Length and Breath will be more compared to thickness and so brittle will act...

09 October 2012 964 2 View

Can anyone share their knowledge about impact factor and indexing?

Can anyone tell me the impact factor of the journals specified below. I saw its Indexing, but I want to know whether they are Excellent or Very good or good or satisfactory or worst. Please kindly...

09 October 2012 1,259 10 View

Turbulence

Is it possible to make a theoretical model to describe the statistics of a turbulent flow (in particular, its internal structures)?Also, under what conditions do smooth solutions to the...

09 October 2012 9,459 2 View

KERS

Can anyone tell me the latest technology advancements and improvements in recent trends of KERS (Kinetic Energy Regenerative System) used in Automobile Braking?

09 October 2012 3,011 1 View

Impact Factor

Which is the best link for viewing the impact factors of the journal. The true and the trusted one?

08 September 2012 6,306 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How do I increase the yield of my PCR product?

Hello, We would like to increase the yield of our PCR product. We are running a series of PCR reactions that is targeting ~1.1kb sequence. We begin each reaction with ~400pg of template DNA...

02 March 2021 4,029 3 View