Simulation of LoRa (Long Range) with GUI

01 January 1970 0 5K Report

I'm looking for a simulation tool for simulating the LoRa (Long Range) communication with the facility of graphical user interface. I have gone through simulation tool like ns2, ns3, packet tracer and net sim, where they is no availability of platform for simulating the LoRa network. Kindly anyone communicate with me, for working on the LoRa network.

Thank you

Vaseem Akram

Badges
Science topic

More Vaseem Akram Shaik's questions See All

Does anyone know, can i do cryosectioning of whole aorta after oil red O staining and use the cryosection parts for further analysis?

I would like to quantify the lesions on aorta. I want to take image of atherosclerotic plaques formation in aorta by using O red Oil Solution. After the staining, what will be the storage...

16 February 2021 5,876 2 View

What is the best concentration of Pam3CSK4 to coat a dish to activate with THP-1?

Hi everyone I am trying to coat a glass-bottom dish with Pam3CSK4 and plate THP-1 cells to measure IL6 with ELISA from the supernatant. I wondered if anyone knows a good concentration and...

21 January 2021 2,593 1 View

How to interface Semi conductor physics and Fluid flow physics in COMSOL?. What are the parameters to be considered while we interface them?

I am using a silicon nano wire in microfluidic channel to identify the some changes in parameters like voltage and current. but i am unable to interface them. the two physics run individually but...

10 January 2021 8,894 1 View

Is there any analytical model to asses impact of rigid projectile on monolithic deformable plate?

I am trying to select suitable element type (Solid or Shell) for impact analysis. I have tried with both solid and shell elements. The results are same for both element types up to certain impact...

08 January 2021 3,251 4 View

Why internal energy absorbed during impact is different when simulated with solid and shell elements using abaqus?

I am trying to simulate high velocity impact of rigid spherical projectile on a rectangular plate using Abaqus Dynamic Explicit. Particulars of Projectile Diameter : 12 mm Mass : 7.05g,...

04 January 2021 10,022 3 View

Can anyone suggest how to find proper OFDM MIMO Simulink model ?

I am doing my research on a communication system. I need a Simulink model with MIMO OFDM anyone of you could suggest me to find the total OFDM transmitter and OFDM receiver Simulink design model

21 December 2020 3,709 1 View

Why I see Lamp-1 GFP in cytocol after transfection?

Hi every one I transfected Lamp-1 GFP plasmid to the HEK293 cell line. When I image the cells in TIRF, I see green fluorescence o the cytosol too. Does anyone have any idea that how it can...

21 December 2020 9,978 3 View

Why HEK293 transfected with LAMP-1GFP do not load dextran?

Hi every one I have made a cell line of HEK293 transfected LAPM-1GFP and after seeding the cells for 24h, I try to load dextran on the dish but after imaging, the cells with GFP+ have loaded less...

14 December 2020 1,801 2 View

What are the tools or software which can simulate climate change for a city and conclude future climate data?

I am working in research on climate adaptation so need to compare the performance of the urban fabric to the climate changes, which requires me to make a comparison and simulation of the...

03 December 2020 988 8 View

Correlation, Regression and significance?

Dears, I have different variables in multiple regression. Two variables are highly correlated. To solve the collinearity issue, I dropped one of them from the multiple regression model. The...

29 November 2020 2,695 4 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How to calculate average trend in maximum annual NDVI from MODIS?

I am wanting to calculate the average trend in maximum annual NDVI in Iceland from 2010-2020 using MODIS MYD13Q1 V6. How would I do this? I have currently inserted the NDVI bands from the MODIS...

02 March 2021 752 2 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View