How optimize the Size Exclusion Chromatography?

Hello! I'll do a size exclusion chromatography, but I only have an open column, and I'll perform the peptide extraction from yeast, using buffer lysis (sodium phosphate 50 mM/NaCl 30 mM/DNAse and...

01 March 2021 2,215 2 View

What does it mean if in mediation analysis the indirect effect is significant but is a larger b value than that of the direct effect?

I understand that for partial mediation to have occured the CI for the indirect effect must not cross zero and the b value for the indirect effect should be smaller than the b value for the direct...

14 February 2021 3,273 7 View

Do you know of an informal caregiver of a person who has recently received a bone marrow transplant?

We are conducting a pilot study of an intervention for informal caregivers of persons who have recently received a bone marrow transplant in the US. If you know of anyone who might be interested,...

13 February 2021 9,174 1 View

How to make Fast Green FCF from powder?

Hi everyone We need Fast Green to electroporate plasmid into mice embryos, therefore we simply need it to see some color in the liquid we are electroporating so that electroporation is more...

07 February 2021 1,671 2 View

Is there a solution to this conundrum on freefall into a black hole?

18 January 2021 1,582 3 View

Lipid Force Field with gromacs command pdb2gmx?

I have a pdb file that contains DPPC molecules and other molecules. I want to generate .gro and .top files from this pdb file using the Gromacs command pdb2gmx. I am trying to use the Charmm36...

08 January 2021 3,751 6 View

LINCS warning only with -pme gpu?

Dear all, I recently bought a RTX3080 and was unable to start the NPT and production steps due to lincs warning (my old gtx 1080ti card ran normally, using the same .mpd), I tried several...

18 December 2020 3,333 2 View

What is the relationship between induction machine stator reactance variation and slip?

It is possible to notice, at some three phase induction machine datasheets, that exists a relationship between stator leakeage reactance and slip, that is, the stator leakage reactance increases...

23 November 2020 2,949 3 View

How to characterize the pore size of membrane filtration with bubble point method?

Hello everyone, I am having troubles with the bubble point measurement to find the pore size of my self-fabricated microfiltration membrane, and I couldn't find a proper answer anywhere else. It...

16 November 2020 7,574 1 View

Is there same kind of limit when annealing two DNA products?

Hi there I'm planning on annealing two PCR products to perform some mutagenesis in a plasmid. I was recommended to try and keep it to 600pb each, for example, but for one of the plasmids there...

15 November 2020 8,656 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View