How optimize the Size Exclusion Chromatography?

Hello! I'll do a size exclusion chromatography, but I only have an open column, and I'll perform the peptide extraction from yeast, using buffer lysis (sodium phosphate 50 mM/NaCl 30 mM/DNAse and...

01 March 2021 2,215 2 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Are protein samples in SDS compatible with ELISA?

I have used an AllPrep DNA/RNA/Protein Mini Kit QIAGEN kit to extract RNA and protein from my samples. At the end of the protein purification, I resuspend my protein in 5% SDS. Will these samples...

28 February 2021 7,370 3 View

Special issue on PLS-SEM in Mathematics. Are you interested?

21 February 2021 5,601 3 View

How to calculate the TCID50 when the highest CPE is 50% or less?

I am doing TCID50 to measure progeny virus and some treatments protected the cells in a way that the highest CPE observed is 50% or less. How should I do the titre calculation in that case? Thank you!

16 February 2021 8,768 1 View

Are there any differences between setting automatic or manual number of measurements in DLS?

When doing measurements in DLS (either size or zeta potential), I have the option to input an automatic number of measurements or to set it manually. My question is: is there a drawback in...

08 February 2021 9,423 6 View

Which drug is better to modify blood pressure in awake monkey, if I provide it in the food or drink reward?

I need to modify the blood pressure in a monkey while is awake in the recording chamber, and I am planing on provide a drug for that in the food or water used for reward... any advise? Thank you

08 February 2021 9,900 1 View

Why stop the reaction in ice for the fluorescent probe FDA (fluorescein diacetate)?

Hi, In literature I noticed that who stains haemocytes with FDA for 30 min then stop the reaction in ice while this does not apply for 15 min incubation time (or maybe authors did not write this...

08 February 2021 3,366 3 View

Why do high doses of humic substances inhibit the growth of corn roots? Is there a toxicity effect?

Length, volume, surface area and dry mass of corn roots treated with humic substances increased up to 13 liters per hectare and decreased with higher doses.

02 February 2021 2,190 4 View

Using a nucleosil c18 column, i get no negative peaks in real time and two negative peaks in post run.Software problem?

Simadzu, lc solutions

02 February 2021 1,969 2 View

What is the status of bread making and more bakery foods with the use of insect flour/powder?

Insects have been consumed by human diet since prehistoric times. At present, the idea of looking at insects as food has been getting traction worldwide, also in response to increasing food...

03 March 2021 6,223 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

Why is the efficiency of viral mRNA electroporation in PBMC low?

Hello, I have been struggling with the electroporation of PBMC with HIV-I mRNA. Although the quality of the RNA generated is good, and the handling of the cells in meticulous, the frequency of...

27 February 2021 9,233 3 View

Alginate and silk fibroin hydrogels toxic to cells?

Hello, I asm currently working with alginate and silk fibroin hydrogels. I prepared a blend of alginate and aqueous silk fibroin (straight from dialysis) and resorted to ionic crosslinking to...

23 February 2021 8,249 2 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

How to reduce static electricity of powder after lyophilization?

I am working on synthesizing and then purifying peptides using the SPPS system. After purification of the peptide, the peptide powder is obtained using a freeze dryer. When measuring the powder,...

22 February 2021 10,099 5 View

What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View