30 August 2023 1 3K Report

I am coding a solid-state NMR pulse sequence on SIMPON (attached file) but I get this error (error: acq overflow in fid points) that I don't know what it means. Does anyone knows what it means?

More Igor d'Anciães Almeida Silva's questions See All
Despite single-cell RNA, how can I characterize a new cell subtype/phenotype?

A new cell subtype was found out only during regeneration phases after a cuprizone-induced demyelination model. How can I characterize this cell? It is important to highlight that was already...

13 February 2021 1,245 1 View

Permanent Fluid temperature initialization in Ansys Fluent?

Dear researchers, I am coupling Design Optimization with ANSYS Fluent in Workbench 2020 R2. I can do the analysis. I am patching the initial Temperature values of the zones. However, the patch...

28 January 2021 4,265 2 View

Strong and extreme winds in the Arctic?

Hello everybody! Looking for a good source of information on strong and extreme winds in the Arctic (monthly values, annual extremes etc.). The form of maps (with isolines) will be most...

25 January 2021 8,984 4 View

Luciferase assay for miRNA-gene: How to obtain DNA (PCR product) from the mutated primer?

To perform the Luciferase assay for microRNA-gene interaction its necessary a primer (wild-type) to amplificate the specific ligation site and also a mutated primer. But if your primer has a...

19 January 2021 8,568 3 View

How to couple Moldex 3D with MATLAB for design optimization of an injection mould?

Hello, I would like to use the software Moldex 3D for the design optimization of an injection mould. How can I couple Moldex 3D with a MATLAB code? Any help appreciated, I wish you all a happy...

09 January 2021 569 2 View

How to setup ANSYS Fluent for simulating the filling stage of an injection mould?

Hello, I am using ANSYS Fluent for simulating the filling stage of an injection mould. However, when comparing the results with those of specialized software, such as Moldex 3D, I found the...

07 January 2021 7,992 1 View

Which plants and trees have the best ability to prevent the entry of particulate matter (PM2.5 and PM1) and nanoparticles in indoor environments ?

In recent years our group has highlighted the importance of trees and plants in public and recreation parks in large mega cities. However, we are interested in developing "green shields" to be...

05 January 2021 6,500 3 View

How to phosphorylate specific residues on pymol?

Hi everyone, I am using the pyTMs plug in on Pymol to phosphorylate a particular threonine in my protein. I am having difficulty in selecting only one or two residues - it seems I can only...

05 January 2021 230 3 View

How to perform Potential Surface Energy Exploration (PES) calculations?

I would like to receive help, as I am trying to make an analysis of the ethanol PES, but the calculations are always giving error. I use the conda-forge version of xtb (* xtb version 6.3.2...

04 January 2021 602 2 View

No title

Dear Colleagues, I need your help. In book (can be found in Internet, free) Todhunter, I., & Pearson, K. (1893). A History of the Theory of Elasticity and of the Strength of Materials (Vol....

26 December 2020 433 1 View

Similar questions and discussions
How do I determine the degree of polymerization of PEG 400 based on NMR integration?

Hello, I am working on the photocatalytic degradation of PEG 400. I would like to know if it's possible to determine the degree on polymerization based on NMR integration, or by the MW of the...

02 March 2021 6,186 3 View

Do you know any MR image dataset?

I would like to research on MR images (0.5T and 3T). Can you please suggest some websites that I can download dataset including both 0.5T and 3T MR images? Thank you.

02 March 2021 7,735 3 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

What could be some reasons why unstimulated monocytes are getting activated?

Im doing PBMC isolation -> CD14+ enrichment using magnetic beads -> stimulation setup. My negative control is just cells in cRPMI but they seem to get activated over and over again.

28 February 2021 7,883 3 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

How to include original NMR data in a manuscript?

hello. i am junior researcher. I received a comment from a reviewer that he could not find NMR data in my submitted paper. I had included the NMR graph with explanation and formula to calculate...

27 February 2021 734 4 View

How to overcome convergence issues in concrete arch models?

Hi, I have modelled a three-span arch bridge with soil fill over along with pedestals. The FE modelling is done in LUSAS with HX8M solid elements (i.e. 3D solid modelling). The non-linearity is...

20 February 2021 1,346 2 View

Solid Phase Extraction of drug product containing nanoparticles ?

Hi Everyone, I am trying to develop an SPE method for the vaccine which contains Matrix-M (saponin Quillaja Saponaria ) which is in nano-particle form and size is around 40nm. These nanoparticles...

16 February 2021 1,389 2 View

Is there a paper that shows the effect of the thermal conductivity of solid electrolytes on lithium secondary batteries?

I want to know the effect of thermal conductivity characteristics of solid electrolytes on the all-solid battery, but I don't know which paper to refer to. Is there a paper on thermal behavior?

15 February 2021 8,806 2 View

How to detect uv vis spectrum of nanoparticle under 300nm?

I try to make the indium nanoparticle and check the uv vis spectrum. I heard that In nanoparticle has surface plasmon resonance peak at 200~300nm. But most of solvent has absorption peak under...

14 February 2021 6,950 15 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close