Simple comsol module for ultrasonic piezoelectric transducer

08 August 2017 0 4K Report

I am looking forward to create a simple comsol module for ultrasonic piezoelectric transducer over a water and find the pressure profile of it, any help??

Badges
Science topic

More Mohamed Afifi's questions See All

How to measure phase difference by stanford lock in amplifier?

how to measure phase difference by stanford lock in amplifier? the data is very fluctuating. I am working on measuring change in length in micro scale by laser interference using the lock in...

02 March 2017 8,252 1 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

How to get LP fiber modes directly from Comsol?

Hi there, I'm new to modelling with comsol. I would like to ask if it is possible for comsol to output linearly polarized (LP) modes? I tried modelling a simple single mode fiber with an enlarged...

23 July 2024 4,019 3 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

Can anyone help with this comsol error? Pleaaaase I need help !!?

Undefined variable. - Variable: comp1.cNa - Géométrie: geom1 - Domaine: 1 Failed to evaluate expression. - Expression: comp1.cNa - Affichage: Graphique sur ligne 1

19 July 2024 1,938 2 View

Why electrical charge on the moving plate increase?

Hi, everyone This figure depicts a simulation of an electrostatic energy harvesting system in COMSOL Multiphysics software. My question is regarding the relationship between the changes in...

19 July 2024 4,694 4 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

Why does the error "The relative error (0.29) is greater than the relative tolerance" appear in Comsol Multiphysics?

Hello, My name is Radu Jubleanu, I am a PhD student at the Politehnica University of Bucharest. I work in the field of magnetic storage in superconductors. I want to carry out a numerical study of...

15 July 2024 6,025 1 View

How to use stress and displacement results from 1st stationary simulation as initial conditions for 2nd eigenfrequency simulation in COMSOL?

Dear All, I am trying to define the dispersion curves of a periodic unit cell in COMSOL Multiphysics with prescribed displacements. I am using two separate studies: - Study 1: Stationary, with...

13 July 2024 7,855 1 View