Despite single-cell RNA, how can I characterize a new cell subtype/phenotype?

A new cell subtype was found out only during regeneration phases after a cuprizone-induced demyelination model. How can I characterize this cell? It is important to highlight that was already...

13 February 2021 1,245 1 View

Permanent Fluid temperature initialization in Ansys Fluent?

Dear researchers, I am coupling Design Optimization with ANSYS Fluent in Workbench 2020 R2. I can do the analysis. I am patching the initial Temperature values of the zones. However, the patch...

28 January 2021 4,265 2 View

Luciferase assay for miRNA-gene: How to obtain DNA (PCR product) from the mutated primer?

To perform the Luciferase assay for microRNA-gene interaction its necessary a primer (wild-type) to amplificate the specific ligation site and also a mutated primer. But if your primer has a...

19 January 2021 8,568 3 View

Any suggestion of free of charge questionnaires that measure mood states?

I need a free of charge and short questionnaire that measures mood states. The questionnaire will be used as in a neuropsychological evaluation study. It is well known that mood states can...

16 January 2021 8,284 4 View

Which peak should I consider when calculating ZIF-8's crystalline size from XRD?

Hello, Using the Scherrer's equation, one could calculate, roughly, the crystalline size of ZIF-8. However, I am confused as to which peak in the XRD pattern should be taken for the calculation?...

10 January 2021 8,633 3 View

How to couple Moldex 3D with MATLAB for design optimization of an injection mould?

Hello, I would like to use the software Moldex 3D for the design optimization of an injection mould. How can I couple Moldex 3D with a MATLAB code? Any help appreciated, I wish you all a happy...

09 January 2021 569 2 View

How to setup ANSYS Fluent for simulating the filling stage of an injection mould?

Hello, I am using ANSYS Fluent for simulating the filling stage of an injection mould. However, when comparing the results with those of specialized software, such as Moldex 3D, I found the...

07 January 2021 7,992 1 View

Which plants and trees have the best ability to prevent the entry of particulate matter (PM2.5 and PM1) and nanoparticles in indoor environments ?

In recent years our group has highlighted the importance of trees and plants in public and recreation parks in large mega cities. However, we are interested in developing "green shields" to be...

05 January 2021 6,500 3 View

How to phosphorylate specific residues on pymol?

Hi everyone, I am using the pyTMs plug in on Pymol to phosphorylate a particular threonine in my protein. I am having difficulty in selecting only one or two residues - it seems I can only...

05 January 2021 230 3 View

How to perform Potential Surface Energy Exploration (PES) calculations?

I would like to receive help, as I am trying to make an analysis of the ethanol PES, but the calculations are always giving error. I use the conda-forge version of xtb (* xtb version 6.3.2...

04 January 2021 602 2 View

How to normalise data on OPM package from R Studio ?

Good afternoon, I recently used OmniLog from BIOLOG for my experimentations : I tested the metabolism of different strains on 2 types of plates. I have 16 strains of 3 different groups...

02 March 2021 3,584 1 View

How to plot the probability paper of Gumbel distribution using R programing?

In R-studio, there are many commands of Gumbel package. Arguments are also different. I`m asking about the alpha parameter of the Copula which must be greater than 1. If this is the one used to...

25 February 2021 5,229 3 View

Has anyone had luck using cell lines other than HEK 293 (such as COS1) to package lentivirus?

I am looking to package lentivirus in endothelial cells but I am opposed to using 293 cells due to personal ethics regarding the source. I have done some reading and saw that COS1, COS7, & CHO...

25 February 2021 3,030 1 View

No title

25 February 2021 5,713 1 View

Implementation of chance-constrained optimization problem via scenario approach?

23 February 2021 7,826 2 View

Fictitious Boundary Meshing Method (FBM) in Commercial FEA software?

Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?

22 February 2021 2,968 1 View

Are there packages (R or Python) for simple models (bucket?) to assess soil water content?

Hi everyone. I am researching droguht effects on soil water drought. I am looking for already implemented functions in R or Python to estimate soil water content from precipitation,...

21 February 2021 2,084 1 View

How reliable are degrees of freedom for lme mixed models in nmle package?

I am running mixed models analyses because I have participants nested in groups. Across the different analyses, I have very different degrees of freedom in the lme output with nlme package (and...

09 February 2021 6,767 3 View

Which software is the best to model a non-linear concrete (ABAQUS, ANSYS,ADINA, ATENA, etc.)?

What is the best finite element modeling software packages for modeling non-linear and fracture analysis of CONCRETE? I've had some with ABAQUS standart/explicit, but I would like to learn if...

27 January 2021 330 6 View

How plot results of membership function in R?

I am using the FRBS package, I developed the model without learning data and I use the plotMF function of this package to see the membership function of every input and output variables. I got the...

22 January 2021 2,668 3 View