Are there any exception like work hardening in metals elastic limit due to dynamic loading?

The samples made out of spring steel are taken from same lot. The specimens were shaped following heating to forging temperature - Forming- Hardening -Tempering methods. After storage of almost 6...

11 February 2021 952 6 View

Regarding to presentation of pairwise comparison of data?

22 January 2021 8,648 1 View

What is the main advantage of using observer based fault tolerant controller(FTC) for sensor fault tolerance?

I am working on FTC for handling sensor faults in the system. I have read about observer-based FTC schemes which use error threshold-based logic between the states and estimated states. If a...

10 January 2021 5,771 2 View

Can a luenberger observer (even a modified version) be effective for a nonlinear affine system?

I want to know whether a luenberger observer or a modified form of it be effective for estimating the states of a system of the following forms: 1. x_dot = f(x,u,d); y = x 2. x_dot = f(x,u); y =...

20 December 2020 1,392 4 View

How much Tensile strength and hardness can be acheived in Aluminium 7050 MMC with B4C reinforcement?

I have conducted research on characterisation of Al7050 + B4C by electromagnetic stir casting. The alloy employed in the process is casted alloy and the Composite too is casted. How much strength...

16 November 2020 9,226 3 View

Why whitefly prefer not to infest Pigeonpea?

Whitefly, Bemisia tabaci is pest of broad host range. In pulse crops, it generally infests greengram, blackgram and cowpea but not Pigeonpea. There might be some biochemical or morphological...

09 November 2020 9,199 3 View

Can u suggest how to identify the matrix material and reinforcement particle distribution in the MMC of scanning electron miroscopy (SEM) images?

How to identify the reinforcement particle behavior in SEM images

09 November 2020 8,664 3 View

Can someone help me in designing off-MPPT mode in a Standalone DC Microgrid?

I am working on voltage control of a Standalone DC Microgrid consisting of Single PV source, a battery and loads. The PV is interfaced through Buck converter to the DC bus, the battery is...

01 October 2020 7,071 2 View

Modeling pure shear loads in Abaqus?

I am trying to simulate a pure shear loading on a cubical block with a single brick element. While I am simulating the other stress components are not getting zeros. Can anyone suggest to me how...

22 September 2020 7,649 3 View

Can anyone suggest any introductory book on tensor analysis and tensor calculus for continuum mechanics?

I have searched google. But it would be more helpful to get suggestions from personal experience.

14 September 2020 5,426 5 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View

Fictitious Boundary Meshing Method (FBM) in Commercial FEA software?

Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?

22 February 2021 2,968 1 View

How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?

How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?

22 February 2021 5,408 1 View