In PRIMER, is it possible to downweight certain taxa in multivariate community datasets to reflect uncertainty around identification??

I have a dataset with about 80 different species. As usual, some species are very easy to identify with certainty whereas others are more difficult, which means that I am less certain of my...

03 March 2021 8,066 4 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View

How to remove DCU and HOBT from my reaction?

I am doing a acid and a chiral amino alcohol reaction using DCC and HOBT in DCM or THF? Can anyone suggest me how to remove DCU and HOBT from a reaction mixture??

28 February 2021 2,153 1 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

How to determine solutionizing time for cast Al alloys?

For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys

23 February 2021 8,839 3 View

Which thermal conductivity test recommended for Ag-Cu nanofluid?

I have prepared Ag-Cu alloy with polymer coating upon it.... how can I measure thermal conductivity of it ?

22 February 2021 5,915 3 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

What are damage parameters for SMA while modelling on ABAQUS 2020?

I have given Elastic and Superelastic material properties, but I think we need to provide the damage parameters also. Please help me here.

16 February 2021 8,694 1 View

Are there alternatives to the Devarda alloy when estimating nitrogen?

Are there alternatives to the Devarda alloy when estimating nitrogen? devarda alloy is reducing the nitrate to ammonium

15 February 2021 8,838 3 View

Passivation of chromium cast Iron in high temperature?

14 February 2021 2,157 3 View

How can we quantify martensite in Ferrous and Titanium alloys?

How can we quantify metastable phases like martensite in Ferrous and Titanium alloys, in relation to their stable counterpart For example in EBSD, XRD, Optical? Eg, Martensite and Ferrite maps.

09 February 2021 7,572 3 View

About forging of Mo Alloys ?

Hello dear Academicians, I am working on the forging of Mo alloys, but I wanted to consult you on an issue I could not solve. Mo is easily oxidized during forging and MoO3 is formed. Is it...

09 February 2021 1,989 3 View