Can someone point me in the right direction for export coefficients for modeling Pollutant modeling. Thanks in advance.
This is a bit vague. Are you presuming some particular software perhaps?
Dudley J Benton No, ranges. When I use PLOAD the information is not correct for the ranges with pollutants given by land use categories.
Is "PLOAD" some sort of proprietary software? Google has never heard of "PLOAD".
Dudley J Benton Pollutant Loading Estimator
It has been many years since I worked with CH2M-HILL (the developers of PLOAD).
Dudley J Benton I fully figured out how to use PLOAD using the export coefficients. Thank you for your help.
During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...
06 August 2024 726 3 View
Hello all, I have been trying to follow a 2-stage PCR protocol used to amplify barcodes of a large yeast library, as per Nyugen et al. (2022) -...
30 July 2024 841 2 View
When I run autogrid4 it says: autogrid4: ERROR: Unknown receptor type: "Cr" -- Add parameters for it to the parameter library first! Look forward to your reply.Thank you so much!
29 July 2024 488 0 View
Hello everyone, I am facing a consistent issue in my NMR spectra with an unwanted peak appearing at 1.25 ppm. This peak seems to vary with the amount of sample: it becomes more pronounced with...
15 July 2024 9,065 4 View
I'd like to know if anyone has got experience in intracerebroventricular (ICV) AAV inj. I am looking for a concomitant spread of the AAV including but not limited to the motor cortex and the...
12 July 2024 781 0 View
Kindly provide their URLs. Thank you
30 June 2024 8,475 0 View
I have been working in Hanoi University of Public Health. I would like to know where and how I can buy AMOS software?
28 June 2024 6,593 1 View
I am working on a small signal stability analysis of a power system on a power electronic load. The power electronic load is modeled as a voltage-dependent load and has the relation attached in...
26 June 2024 2,496 1 View
Dear All, I want to cut PDMS sheet with thickness of 0.8 mm to rectangular shape with Graphtec cutter plotter CE6000-40. What condition do you offer? Do you offer any kind of special speed or force?
25 June 2024 8,111 1 View
As the New JCR impact factor is just released. I need a list of journals which are not tracked for impact factor this year or which are delisted by JCR. Thanks!
24 June 2024 6,586 2 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
Approximate concentrations are require in compared with the WHO permissible limts
11 August 2024 2,723 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I have incorporated the dispersion effect for the OPBE functional by specifying the S6, SR6 and S8 parameters for GD3 in Gaussian G09 package. For this purpose, I have defined the environment...
05 August 2024 1,494 2 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View