3D printing technology for films or patches
Between 0,4mm to 0,8mm.
If you choose 0,4mm the speed decrease but the precision improve.
If you choose 0,8mm the speed can be increased and the precision is lower.
Thank you Daniel.
0.3 mm dia nozzle is advisable for 90 deg deposit angle.
I have a response variable called skin yellowness, which I will measure via a scored color chart, whereby 1 is pale yellow and 15 is orange. I'm not sure if this counts as an ordinal variable,...
11 August 2024 4,793 1 View
Approximate concentrations are require in compared with the WHO permissible limts
11 August 2024 2,723 1 View
how can I read Waters, R. S. 1958. Morphological mapping. Geography 43 :10-17 from internet? note: not in google or resaearch gate
26 July 2024 7,813 3 View
How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...
26 July 2024 8,281 0 View
Despite not having cells in the media, I am getting purple color. I have tried many troubleshooting methods, varying media types, and even different MTTs from different companies to figure out the...
21 July 2024 9,914 1 View
As PhD student specialized as food and industrial microbiology need to further research on bacteriocin and fermented food.
16 July 2024 7,394 1 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
What are some of the areas to consider in undertaken research in educational administration in MPhil.
14 July 2024 8,394 2 View
XRD analysis
08 July 2024 977 4 View
how i can calculate mathematically COD concentration if i add 1gr from glucose to 1 L distilled water
08 July 2024 9,104 2 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
How can I measure the thickness of thin film by Uv-Vis?
06 August 2024 7,810 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...
30 July 2024 4,671 3 View
Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...
30 July 2024 906 2 View
Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...
29 July 2024 1,092 2 View
Your comments
28 July 2024 2,822 2 View
My final research is about making chitosan/pva hydrogel for wound healing using gelatin as crosslinker. Last month, i made the thin film hydrogel and it turn well. It was okay. Last week, i make...
28 July 2024 2,794 6 View
Novel areas especially
24 July 2024 8,416 0 View
Hello, I am experiencing an issue with mixing micro powder with resin in a 3D printer. The problem is that sedimentation occurs after a short period (about half an hour to an hour). Could you...
23 July 2024 1,672 0 View