Is it possible to model plastic behavior of fiber reinforced polymer composite in Abaqus (without using subroutines)? As u know, just elastic behavior for lamina can be defined in property module.
Yes you can if you have the experimental plastic curve of the material you can introduce it in the software with Yield stress/strain
and how can I introduce this plastic behavior for different directions?
Assume I have an explicit problem with 1 step (which itself has "n" time increments). I need the nodal results after each increments during the solution, not when the solution is completely...
08 September 2019 7,193 3 View
Is it possible to define initial density for powder compaction in ABAQUS using DPC material model? I couldn't find about this. I think the compaction behavior will differ with different initial...
06 July 2014 2,436 5 View
Drucker Prager Cap model for ALUMINUM These data are needed for simulation of powder compaction in Abaqus.
05 June 2014 3,670 0 View
For modeling powder compaction, the best model seems to be the "Modified Drucker-Prager (Cap Plasticity)". What model is best suited for elastic behavior of powders? (Between elastic & porous...
02 March 2014 6,443 1 View
What is the best material model of ABAQUS to simulate powder compaction behavior? Mohr-Coulomb, Drucker-Prager, Cap plasticity, etc?
02 March 2014 10,285 1 View
As known, a shock wave is induced when the plastic stress wave becomes faster than the elastic one. Can anybody suggest to me how it's possible to make shock waves in metals like steel using an...
31 December 2013 3,104 18 View
I want to do a sequentially coupled thermal-displacement analysis in Abaqus. At first, doing a heat transfer problem, and then, having the nodal temperature from the last analysis, performing a...
11 December 2013 8,531 52 View
How can I obtain dislocation density using XRD? What about XR micrograph or XRD topograph?
10 November 2013 7,433 3 View
I used some etchants like keller and kroll, but I didn't get any results. Is there any chemical solution for this or must I use electroetching?
09 October 2013 509 3 View
Plasticity behavior of lamina.
09 October 2013 2,530 2 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...
29 July 2024 9,572 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...
20 July 2024 647 2 View
Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...
17 July 2024 1,501 1 View
I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...
16 July 2024 8,436 0 View
Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...
15 July 2024 3,491 0 View