11 November 2013 3 7K Report

How can I obtain dislocation density using XRD? What about XR micrograph or XRD topograph?

More Amir Atrian's questions See All
Is it possible to get ABAQUS/Explicit results (e.g. the nodal displacements) after each increments during solution?

Assume I have an explicit problem with 1 step (which itself has "n" time increments). I need the nodal results after each increments during the solution, not when the solution is completely...

08 September 2019 7,018 3 View

How can define "initial relative density" of powder through modeling powder compaction in ABAQUS using Drucker-Prager Cap (DPC) model?

Is it possible to define initial density for powder compaction in ABAQUS using DPC material model? I couldn't find about this. I think the compaction behavior will differ with different initial...

06 July 2014 2,229 5 View

Can anyone help me to find "cap hardening behavior" and "cap model parameters" for Al7075 in literature?

Drucker Prager Cap model for ALUMINUM These data are needed for simulation of powder compaction in Abaqus.

05 June 2014 3,541 0 View

Elastic behavior of metal powders within compaction in Abaqus?

For modeling powder compaction, the best model seems to be the "Modified Drucker-Prager (Cap Plasticity)". What model is best suited for elastic behavior of powders? (Between elastic & porous...

02 March 2014 6,243 1 View

What is the best powder compaction model in ABAQUS?

What is the best material model of ABAQUS to simulate powder compaction behavior? Mohr-Coulomb, Drucker-Prager, Cap plasticity, etc?

02 March 2014 10,003 1 View

How to make a shock wave in solids with impact?

As known, a shock wave is induced when the plastic stress wave becomes faster than the elastic one. Can anybody suggest to me how it's possible to make shock waves in metals like steel using an...

31 December 2013 2,962 18 View

How can I transfer analysis results to second analysis in Abaqus?

I want to do a sequentially coupled thermal-displacement analysis in Abaqus. At first, doing a heat transfer problem, and then, having the nodal temperature from the last analysis, performing a...

11 December 2013 8,349 52 View

How can I etch Al7075 to view grain boundaries?

I used some etchants like keller and kroll, but I didn't get any results. Is there any chemical solution for this or must I use electroetching?

09 October 2013 376 3 View

Is it possible to introduce plasticity behavior of fiber reinforced composite to Abaqus (without using subroutines)?

Plasticity behavior of lamina.

09 October 2013 2,412 2 View

Plasticity behavior of lamina in ABAQUS?

Is it possible to model plastic behavior of fiber reinforced polymer composite in Abaqus (without using subroutines)? As u know, just elastic behavior for lamina can be defined in property module.

09 October 2013 5,792 2 View

Similar questions and discussions
How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How to calculate average trend in maximum annual NDVI from MODIS?

I am wanting to calculate the average trend in maximum annual NDVI in Iceland from 2010-2020 using MODIS MYD13Q1 V6. How would I do this? I have currently inserted the NDVI bands from the MODIS...

02 March 2021 752 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close