Orthrotropic stress and strain limit Calculation in composite simulation in ansys?

06 March 2024 1 2K Report

Hello altruits, would you please help me on how to calculate orthrotropic stress and strain limit in composite simulation in ansys?

Thank you so much!

Hussein Farroukh

Calculate the orthotropic stress and strain limits based on the material properties and ultimate strength or ultimate strain values you defined earlier (material properties).

If it's all done, you can use the postprocessing tools to extract the stress and strain in each direction.

Badges
Science topic

More Gazi A. Raihan's questions See All

What books will you recommend for doing research about Generalized power series rings?

I'm currently studying in mathematics major, undergraduate program and doing my very first scientific writing and research. The topic that I get is about "Generalized power series rings", but I...

26 August 2020 6,272 3 View

Which tool will be best for analysing Bio-medical datasets using deep learning(a vast field of machine learning)?

I need to predict disease with the help of deep learning. If you know about these then please help me find my way. In the following, I add my dataset of ovarian cancer. It's taken from a hospital...

31 December 2019 3,816 2 View

Is there any algorithm in deep learning for analysing datasets?

Please briefly explain with the best modal you know and also tell me about the code.

20 December 2019 5,132 10 View

How many types of research methodology and which one is very much effective for Civil Engineering Research ( Structural Engineering Research)?

How many common types of research methodology and which one is very much effective for Civil Engineering Research ( Structural and Earthquake Engineering Research)?

02 October 2019 6,630 8 View

How to overcome overfitting in WEKA?

How can i remove over-fitting in weka. I have used re-sample, randomize techniques. But whats the proper way to remove over-fitting in weka.

24 February 2019 6,988 9 View

How to find data related to flood ?

I am trying to do flood prediction on big data. I am looking for flood, water level, condition of soils. Any one have any idea where i can get these data.

12 February 2018 1,943 3 View

I have been using the same dna primer and same dna sample for pcr. Suddenly there are only dimers. How come?

I have checked the extracted DNA in horizontal gel electrophoresis and it seems oak. Freshly diluted DNA and primer before working to solve the problem but that did not help. I was getting...

26 November 2017 5,804 7 View

What are the effective k points in Auger Recombination Rate/Impact Ionization Rate calculation using supercell?

For DFT or TB or any scf calculation supercell is needed to include the defects in material. Now I get the the converged eigen energy and eigen vector at supercell k vector. I can unfold the band...

30 August 2017 7,735 2 View

How to calculate qualitative sediment concentration using Landsat Image??

How to calculate qualitative sediment concentration using Landsat Image!! Which software is good to use--ERDAS or ArcGIS??

02 July 2017 4,287 6 View

I have a set of data with wind speed (knots) for a particular tropical cyclone. How can I calculate Pressure Drop from these datas?

15 June 2017 4,849 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View