Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

Why tick's salivary gland extract didn't run in the gel (SDS PAGE )??

Greetings, I want to make SDS PAGE for my sample (Tick salivery gland extract), I tried concentrations 10%, 12%. I also tried high molecular weight ladder. But the protein stopped at the top and...

25 February 2021 7,698 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

How to measure the pH of Peat Soil?

Peat possess organic content above 75% and is highly acidic in nature (i.e. pH < 4). Before commencing stabilization, it is mandatory to know about the pH level of peat. Therefore, your...

18 February 2021 9,424 7 View

How to Measure Consumer Willingness To Change from petroleum-fueled vehicle to electric vehicle?

I wanted to calculate the probability of one consumer shifting from using a petroleum-fueled vehicle to an electric vehicle. Since my background is in engineering I do not know much about how to...

15 February 2021 9,190 5 View

Having trouble mounting the sections on the slides for IHC staining, what solution should I use?

Hello everyone, I just started learning IHC staining and I have some frozen sections to practice with in a 96-well plate. I'm having trouble mounting the sections on the slide, a colleague told me...

08 February 2021 6,880 3 View

How to use Image Lab to take an image for the bands and the ladder in the same image merged together in Western Blot?

Hello everyone. I was trying to use Image Lab software to take an image of both the ladder and the samples merged together in one image to see the position of the bands according to the ladder MW,...

04 February 2021 9,996 2 View

Need a research paper for multi speaker and single microphone acoustic echo cancellation?

Hi, I am working on a problem that involves multiple smartphones/tablets. All devices are playing the same sound with synchronization difference up to +- 5ms. Now, there is an echo issue and I...

02 February 2021 5,929 3 View

Can I use the result from a pilot study to decide the minimum sample size ?

Can I use the result from a pilot study to decide the minimum sample size required to compare the means using independent sample t-test ? Or any other way that can help me to determine the...

29 January 2021 7,677 6 View

How to prepare secondary antibody from lyophilized antibody?

So I'm new to lab research and learning Western Blots these days. I ordered my secondary antibody and it arrived in a powdered form. Here is the...

27 January 2021 5,402 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

How to extract the y+ value from fluent ?

I am doing a 3D steady simulation of a wind rotor using Ansys Fluent. In order to have a y+ of 1, I created 10 inflation layers using total layer thickness method, and I started a first...

23 February 2021 2,819 3 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

How do I add a udf to Ansys fluent and does it need to be compiled before hand ?

I have a Define_CG_Motion udf written in c where do I add it to my Ansys fluent project and does it need to be compiled before that?

21 February 2021 9,347 3 View

How do I plot Pressure against crank angle degree in Fluent?

18 February 2021 8,390 3 View