CNT coating on copper using dip coating?

I need to disperse the CNT nanoparticles available with me and make a solution which can be easily dip coated on a copper surface. Anybody having experience in this?

04 May 2018 2,671 2 View

How to measure the contact angle of FC-72 over metal surfaces?

Dielectric fluid FC-72 is highly volatile in nature and thus is very difficult to measure its contact angle over plain and nanostructured surfaces. Is there any method by which we can measure the...

11 December 2016 3,292 6 View

Role of three electrode system?

What is the importance of three electrodes system in the electrodeposition of nanostructures on copper substrates? Why Pt electrode should be used as the counter electrodes in the coating procedure?

03 April 2016 9,164 1 View

Range of values for electrodeposition of Nanowires???

For the fabrication of nanowires using electrodeposition method and alumina templates some journals are available. But, the corresponding values for the fabrication using electrochemical...

01 February 2016 7,290 0 View

Can anyone help explain my Magnetron Sputtering of graphite target results?

I am trying to do sputtering of graphite target of 4" dia and 3 mm thickness on copper substrate. The distance between the target and the substrate is 6cm and substrate temp is 35 deg C. Ar gas...

31 December 2015 3,732 10 View

How can we increase the performance of vertically aligned carbon nanotubes for electronics cooling?

09 October 2015 5,038 2 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Is there any test to determine the cardiovascular risk of patients with obesity? from the perspective of obesity?

We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...

02 March 2021 6,036 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View