MCMC inference for COVID-19 SEIR model?

08 June 2020 1 6K Report

Hi,

I have a standard SEIR model and would like to run a simple Bayesian MCMC (Metropolis-Hastings) inference on COVID data. How do you do this on R?

Many thanks!

Safaa K. Kadhem

https://cran.r-project.org › webPDF

Package 'EpiILM' - CRAN

Badges
Science topic

More Zakariah Gassasse's questions See All

Is there any ergonomic standard or guidelines for standing, lifting, or carrying of weight?

Is there any ergonomic standard or guidelines for standing, lifting, or carrying of weight? Such as what is the height of table for those who are performing standing work, what are the radius of...

22 March 2016 6,379 13 View

Anyone familiar with BOD and COD reading at wastewater pH below than 4?

Dear all, Can you please help me on this matter. Right now, i am doing some research at Physical Chemical Waste Water Treatment Plant. This company using Sulphuric Acid (98%) and Caustic Soda...

08 June 2015 9,246 6 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

AUX gas reading problem on QE with full MS and PRM method in one run?

Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...

06 August 2024 4,953 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

E-commerce businesses, COVID-19 and Entrepreneurial Strategies (innovation, proactiveness and risk-taking)?

Hello: I am looking for articles that address e-commerce businesses and COVID-19 survivors, as well as Entrepreneurial strategies that reflect e-commerce businesses. Blessings Evelyn Dempsey

05 August 2024 5,332 3 View