Link between microstructure and surface defects

01 January 1970 1 2K Report

Do you think there is a link between the macroscopic surface defects (e.g. as described here: Article A noise robust method based on completed local binary patter...

) and micorstructure? By microstructure, I mean texture, recrystallization, grain size distribution, grain misorientations etc.

Wisam Al-Wajidi

Look for this manuscript "Quasicontinuum analysis of defects in solids"

Badges
Science topic

More Karol Frydrych's questions See All

What substance can I use for DIY recoating of a optical fiber?

During the process of inscription of FBG on the silica/glass optical fiber few centimeters of the fiber had to be stripped. Bare fiber is too fragile for mechanical measurements, so I thought...

10 August 2020 4,823 4 View

Are move probabilities used during MCTS procedure in AlphaGo Zero?

In AlphaGo Zero algorithm, the neural network returns a pair (p, v) consiting of a vector of move probabilities p and a scalar v indicating winning probability. The v is used for node evaluation...

06 June 2020 5,588 3 View

Can discretization method change non-observable system to became an observable one?

Is it theoretically possible, that after discretization by using Talyor Series Expansion, a non-observable nonlinear system will became an observable? It was proved, that used continuous model of...

15 May 2020 3,608 5 View

Did anyone here perform VPSC simulation by imposing stress?

I am trying to simulate the state of internal pressure in a tube using the boundary conditions: \sigma_{rr} = 0, \sigma{theta theta} = X, \sigma_{zz} = \sigma{theta theta}/2 in VPSC. I know how to...

21 November 2019 6,226 1 View

Is there any physicochemical data which tell which of two polymers will be on the surface after the 3D printing?

Hi, I prepared solvent of PHBV and PLGA in methylene chloride. The resulting slurry was then cast into a Petri dish and dried. The resulting film was used to fabricate composite scaffolds using...

06 November 2019 9,454 2 View

Did someone developed any analytical surface for the Berkovich indenter?

I need the analytical surface describing the geometry of the Berkovich indenter, taking into account the fact that the tip of the indenter is rounded with some radius. The modelling of the...

24 June 2019 4,607 4 View

What is the best animal model for testing the effectiveness of painkillers?

We have a substance that potentially reduces the sensation of pain. We want to study it on laboratory animals. We are looking for a way to measure pain in animals.

04 February 2019 6,146 4 View

Does anyone know a free microstructure generation algorithm?

Hello everyone, I would like to use some program to generate grain structure of a metal. Does anyone know any free code or program? The output data from this program wil be used for FEM...

01 June 2016 7,580 3 View

How reliable is texture measurement from the EBSD.comparing to texture obtained using the X-ray diffraction?

How reasonable is obtaining a polycrystal texture from the EBSD measurement comparing to the results obtained using the X-ray diffraction? Is the typical investigation area in EBSD smaller or bigger?

14 September 2015 1,615 9 View

What is the optimal buffer for DNase I?

I would like to use DNase I (from bovine pancreas, Roche) to get rid of DNA. Roche/Sigma does some recommendations (1 mg/ml enzyme, pH 7.0, Ca 0.12 mM, some Mg), but I did not find a comprehensive...

06 September 2015 9,806 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

Possible problem for showing 0.2 sun intensity instead of 1 sun intensity in AAA class Newport solar simulator?

We have a AAA class Newport solar simulator. We changed the Xenon Arc Lamp recently (XBO450W, Make:OSRAM) as the lifetime got over. However, the intensity is coming to be only 0.2 sun instead of 1...

14 February 2021 9,998 3 View

What causes defect peak broadening?

Say we observe yellow and blue luminescence in GaN, and these defect peaks are always broader than the BE peak. What factors contribute to defect peak broadening? Please help me list out such...

25 January 2021 1,733 3 View

Why can't I get an Sdr value when measuring surface texture parameters?

I am performing a texture surface analysis of a polished ceramic surface using an optical profiler; amongst the parameters I am measuring is the Sdr. I got values for the Sdr when I analyzed my...

25 January 2021 4,462 3 View

What is the best etchant for severely deformed, high purity magnesium?

I have tried using acetic picral and 5% nital solution when observing the microstructure of severely deformed pure magnesium. Unfortunately, I keep getting similar microstructures (as shown below)...

20 January 2021 8,783 4 View

How to recrystallization amine compound and it is not soluble in common organic solvents ?

19 January 2021 671 3 View

How do I know the parameters for calculating the dislocation (edge and screw) density from XRD?

Especially the C12, C44, and Ai values for ferrite pearlite microstructure. Thanks

19 January 2021 9,035 5 View

Density homogenization in Multiscale modelling?

Hello, For now, I am following the integrated technique to derive the mass from the smaller scale (microstructure). Is there any better approach to get the mass of a given macro-structure from...

16 January 2021 4,792 1 View