Is there some correlation beetween thermodynamic functins and hardness of refractory compounds ?

More Pavlo Prysyazhnyuk's questions See All

What for is saturrated sodium chloride solution in ISO 12966-2 ?

Hi, everyone. Our lab is going to use ISO 12966-2 and 12966-4 and there is one moment in sample preparation (rapid transmethylation method under alkali-catalysed conditions) that I can't...

15 September 2020 3,229 4 View

How to deal with a mismatch in 12'' CF flanges?

My turbomolecular pump (Leybold) and vacuum chamber (Pfeiffer) have difference in knife edge diameter of ~0.5 mm. This results in a noticeable camber in the used gasket and the pressure not going...

23 September 2018 9,077 3 View

Do I need a wedge in KBr windows in my FTIR setup?

I am in the process of building a new setup and have a discussion with my colleague on the subject. We will measure several monolayers on a flat reflective surface inside a vacuum chamber with ~1...

08 August 2018 9,301 2 View

Multiscale modeling of steel microstructure

Hi, I'm in interested in contacts with scientists who are involved in steel microstructure multiscale simulation during thermo-mechanical treatment, namely, for severe plastic deformation (SPD)

11 January 2011 5,236 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

What is the error of the Txy diagram?

Hi, I know the attached Txy diagram has an error but can't figure it out. Could you please look at the diagrams and explain it to me?

23 February 2021 4,239 1 View

How the values of errors can be calculated for thermodynamic data?

I have calculated thermodynamic parameters for surfactant solutions in aqueous and mixed alcoholic solvents. I want to calculate the value of errors in the data and represent it in the table along...

22 February 2021 239 2 View

How much quantity of water I have to add for wet milling of aluminosilicate refractory powder?

I want to mill Aluminosilicate refractory powder. I have 7-micrometre aluminosilicate refractory powder and I am going to do wet milling. I want to know how much water to be added to the wet...

07 February 2021 2,829 2 View

Is it possible to calculate entalphy of LiBr/H2O or another solution if we know correlation of specific heat without using any software?

17 January 2021 5,522 3 View

How can I get oil properties in 300-30000K temperature range?

I need thermophysical and electrical oil properties to investigation of DC discharge in oil. Are multicomponent mixture models effective and precise in such calculations? If yes, what MC-modells...

04 January 2021 9,080 8 View

Can anyone help to get ansys-fluent tutorial zip files ?

I need the following tutorial zip files to learn the basics of the software: Using sliding and dynamic meshes Modeling solidification Using the Eulerian Granular Multiphase Model with heat...

03 January 2021 5,571 5 View

The > 91 Years long collective IQ Blunder ?

Never before was there a bigger blemish. Namely: Not to collectively underastand Zwicky's discovery of Cryodynamics, as his sister to deterministic Thermodynamics came to be called later. Dec....

30 December 2020 8,300 5 View

How to rectify the miscomputation of Pressure and Continuity in HVAC CFD Simulation Using OpenFOAM?

I'm using OpenFOAM to run a CFD study of thermal comfort within a hall. I'm using OpenFOAM v1912 and BouyantBoussinesq(Simple&Pimple)Foam solver. eI have 6 inlets and outlets each with specific...

21 December 2020 1,303 3 View

Gourav Mundhra

Dear Pavlo Prysyazhnyuk

With the newer builds of Thermo-Calc there is a added module, Property model calculator. In this particular module in the the general models there is a model to predict the Yield strength and from that some of the mechanical properties can be calculated. Do check it out for more information at https://www.thermocalc.com/products-services/property-model-libraries/general-models/.