Do we have any empirical model to model the combined effect of carbonation and chloride attack in concrete concerning climate change?

Do we have any empirical model to model the combined effect of carbonation and chloride attack in concrete concerning time-dependent temperature, relative humidity and concentration of carbon dioxide?

08 February 2021 4,277 1 View

What is the reference value of THD in BLDC MOTOR speed control ?

i used to control EHO+ANFIS to MRPID to Landsman converter for bldc drive i got 7% but some of them are telling IEEE standards are < 5% is it correct for Drives ?

07 February 2021 5,892 1 View

How do I remove tetrabutylammonium perchlorate after electrolysis of organic molecules?

I am doing electrochemical oxidation of organic compounds for the the synthesis of nitrocompounds from simple organic molecules. I want remove supporting electrolyte after electrolysis. Please...

03 January 2021 7,858 2 View

Could not get reduction peak for Mxene Counter electrode in Iodide electrolyte, why?

I have deposited MXene Ti2C2Tx mixed with tritonX binder and heated at 250 C for half an hour in ambient air conditions on FTO glass substrate, the deposition technique followed was doctor...

28 November 2020 2,330 6 View

What are the best binder which can be used for deposition of MXene on FTO?

I would like to coat MXene (Ti3C2Tx) on FTO glass substrate using doctor blade deposition technique, for which i think a binder is essential for the adhesion of MXene onto the FTO. The post...

28 November 2020 9,360 3 View

Kindly suggest the best organic solvents used for dispersibility of graphite powder?

Kindly suggest me some good papers regarding a comparative study on various organic solvents used as dispersion medium for graphite powder. The application is to make a graphite paste and used the...

24 October 2020 1,586 4 View

What are the best used slurry to coat on TCO using doctor blade method?

I'm trying to deposit TiO2 onto FTO beforehand I would also like to have some knowledge on the other different types of slurry consisting of different materials to coat on TCO using doctor blade...

22 October 2020 1,427 1 View

Could anyone please suggest me some papers on using MXenes (Ti3C2Tx) as CE for DSSC application?

I'm currently working on MXenes as Counter electrode (CE) for Dye sensitized solar cell (DSSC) application. I would like to know about the research work being done in this area. Thank you in advance.

14 October 2020 9,448 2 View

Is it possible to coat/mix MXene (Ti3C2Tx) with conductive polymers such as PEDOT or PANI?

Could anyone suggest me some good papers which involves the coating or mixing of MXenes with conductive polymers such as PEDOT or PANI or any other conductive polymer for that matter.

12 October 2020 5,653 3 View

What are the various methods by which MXenes are deposited on the Transparent conducting oxide glass?

I would like to know the different deposition techniques and the respective conditions and constraints to deposit or coat a layer of MXene (Ti3C2Tx) onto a TCO glass substrate.

04 October 2020 4,616 3 View

Can chitosan alone can act as a reducing agent for Cu(0) nanoparticle sythesis?

[Synthesizing Cu nanoparticles without using chemical reductants]

01 March 2021 8,359 1 View

Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

Uncertianiny in using dry or wet basis in mixing a sediment with fuel oil?

Hello I'm currently working on a topic related to studying the anaerobic biodegradation of TPH in marine sediments. In this work, sediment should be mixed with fuel oil to a concentration of 20 g...

24 February 2021 9,839 3 View

Standard curve shifting over time. How do I stabilise the ELISA?

24 February 2021 1,365 3 View

How can I selectively dry etch Ti on a polymer substrate?

24 February 2021 5,378 1 View

How to reduce static electricity of powder after lyophilization?

I am working on synthesizing and then purifying peptides using the SPPS system. After purification of the peptide, the peptide powder is obtained using a freeze dryer. When measuring the powder,...

22 February 2021 10,099 5 View

Plant research: Watering uniformity/consistency. How important is it?

Trying to gather insight from an unresolved discussion with a colleague here, and either the available literature surrounding this topic and/or my keywords in search of are lacking. Context:...

21 February 2021 6,389 3 View

How does a freeze dryer destruct your solid sample?

Several times I lost my sample during freeze drying. There was no solid or powder in the vial after freeze drying. I'm sure sample contained solute because i took its NMR spectrum. I covered the...

15 February 2021 6,749 2 View

How to measure acetic anhydride solution with 18M sulfuric acid?

I am doing research on the synthesis of paracetamol. I am preparing acetic anhydride solution with a few drops a sulfuric acid and wish to measure the pH of this solution. However my pH meter...

14 February 2021 8,699 3 View

Can i use the " weight moisture" ( humidite ponderale in French) of plants to describe their efficiency in using water?

Weight moisture is : water content/ dry weight , if for example it is 4 it means that this plant have for each 1gam of dry mass 4 grams of water. can i use this to interpret the plant use of...

14 February 2021 5,784 1 View