Is there anyone know about SRM simulation in Maxwell 2D?

Alireza Sahafi @Alireza_Sahafi2

05 May 2016 1 561 Report

I want to know how I can simulate transient case in Maxwell 2D for switched reluctance motor,Please help me.

R. Rebbah

On youtube. good tutorials are availble.

Badges
Science topic

More Alireza Sahafi's questions See All

How can I get the d-axis and q-axis inductance characteristics?

Hello, I've simulated a reluctance synchronous motor in 2D maxwell and now, I want to get Ld and Lq characteristics. Does anybody know about it?

31 December 2017 9,907 0 View

Is anybody know about controlling of the BLDC motor by single - sensor current?

I've simulated a Four-Switch Three-Phase BLDC motor by single current sensor, but there is a little problem in Simulation results,Can anybody to help me?

06 July 2017 6,149 5 View

Does anybody know about DFIG?

I have simulated a DFIG structure in Matlab,When I run the simulation,a error appears. I,ve attached it here. Please check it.

05 June 2017 2,473 5 View

Which kind of the MATLAB version is suitable for coupling with ANSYS Maxwell 16?

Is it possible to coupling Matlab 2013 and Maxwell 16?

31 December 2016 2,269 2 View

How can I design a first - order filter for output of the single-phase VSI inverter in Matlab?

Specification of the single-phase VSI inverter: Vdc=400v load= RL R=10 , L=50*e-3 H reference signal=sin wave (50HZ) carrier signal=Triangular signal (500Hz)

11 December 2016 8,745 0 View

How can I find alloy material data sheet?

I need following data sheet (B-H curve): CoFe SiFe (for designing of the motor core) Please help me.

10 November 2016 776 3 View

How can I desgin TSF method for switched reluctance motor torque control? ?

I want to know,How I can implement TSF method,Assuming that switching angles to be as follows: tetaon=0 tetaoff=18 tetac=30

06 July 2016 7,688 4 View

Is anyone know about current control by PWM method?

I want to know how I can simulate a current PWM controller for a switched reluctance motor,I want to simulate it in Mtlab/simulink, Please help me.

06 July 2016 9,427 4 View

What's the dwell angle (teta off - teta on) range for a switched reluctance motor in the rated speed?

I've simulated a 8/6 SRM in Matlab at rated speed and load, I want to know How much should be the dwell angle? (15 degrees or more)

05 June 2016 2,018 2 View

How can I simulate sensorless fuzzy logic method for a switched reluctance motor in simulink\Matlab?

I want to know how can I simulate fuzzy logic controller blocks in simulink?What is the difference between controller blocks?and what is details related to designing these blocks? These are two...

05 June 2016 5,061 1 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

When I simulate for S parameters using ADS, I have faced this issue that I have attached. Please anyone clarify me?

...

31 July 2024 1,671 3 View

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out?

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out? For example consider a process for certain product manufacture where a new process flow...

31 July 2024 781 1 View

How to restart MD without using checkpint file in GROMACS?

Dear All Gromacs User I would like to restart MD without using checkpint .cpt files? I heard there is a way for acheiveing this. Any input and sugegstions are most welcome. Thanking You Budheswar

29 July 2024 3,084 8 View

How to prepare a molecule for molecular dynamics calculations?

If I want to calculate molecular dynamics (Gromacs), do I first need to optimize the geometry of the molecule? For example, I first draw the molecule in Avogadro, and then what? I guess I can't...

28 July 2024 673 3 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Wrong out put for gmx x2top?

Dear users, I would like to simulate a zeolite structure in gromacs. I got the .cif file from IZA expanded in one direction in Materials Studio and exported a .pdb file. However, when I want to...

24 July 2024 367 4 View

How to create parameter and coordinate files for ligand in amber when FATAL error (maybe due to duplicate bond specifications) happens?

Hello, I'm trying to create parameter and coordinate files for a drug (PRG-A01) found on the following page: http://www.probechem.com/products_PRG-A01.html I used the guide made by Michael...

17 July 2024 3,472 3 View

How to define a zeolite structure with rigid framwork?

Dear Gromacs users, I would like to simulate a zeolite-water system. In different literature, it is suggested to consider a rigid framework of zeolite to decrease the computational cost. I would...

15 July 2024 4,590 1 View