Is there any additive or flux material which can react with nickel to bring it in slag phase out of molten pure copper?
Greetings everyone, I want to optimize the 3A state of a molecule in Gaussian. So, I have set the multiplicity value 3. However, it is taking a long time. Instead of that can I optimize the...
10 June 2024 4,555 3 View
Hii all.. I have few sequences of Fusarium spp partial TEF region. I want to submit them to genebank to get accession numbers. Can someone please help how to submit sequences of coding regions? It...
23 April 2024 2,468 6 View
Greetings everyone, I am trying to dock a planar ligand with a receptor molecule using Autodock tool. I want to freeze the torsions of the ligand. So, I changed the number of active torsions to...
07 November 2023 7,648 3 View
Kindly explain how to calculate all the parameters listed in the image , the below data is for polyetehelyne.
29 October 2023 9,588 2 View
For Superconductor.
07 October 2023 2,613 2 View
Dear all, I need to calculate the value of a fluorophore. Can I use the ground state optimized geometry of the molecule to calculate the value? Also, what is the formula to calculate the total...
12 September 2023 9,697 2 View
I'm using a Gibbs reactor in ASPEN Plus to simulate gasification reaction with restricted equilibrium using temperature approach and getting the following error, kindly help. THE NUMBER OF...
10 September 2023 6,607 0 View
Wet isotropic etching of silicon
16 August 2023 3,363 1 View
I need to simulate biomass gasification in Aspen Plus, for the Pyrolysis Zone I'm using a RYield reactor. I would like to know how can I get the components yield for this process?
05 July 2023 5,924 2 View
I'm using a RGIBBS reactor in Aspen plus with biomass as fuel. I'm getting the following error "TEMPERATURE HIT THE LOWER BOUND. T-LOOP NOT CONVERGED IN 4 ITERATIONS". Could anyone suggest any...
26 June 2023 5,913 2 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
I've attempted to use this method to synthesize copper nanoparticles. Copper nanoparticles can be synthesised using a variety of precursor materials. CuSO4, distilled water, NaOH, and EDTA are...
28 July 2024 8,027 3 View
I synthesized some paramagnetic cobalt and nickel complexes (expected to be Co(II) and Ni(II)) using a bidentate ligand - N of pyridine ring (aromatic) and O of P=O (aliphatic), and I obtained...
03 July 2024 3,410 4 View
If I dope silver during the synthesis of copper indium sulphide nanoparticles by hydrothermal method what will be the size of nanoparticles?
13 June 2024 6,844 3 View
I'm interested in Raney Nickel and its composition. While it's usually a Nickel-Aluminum (Ni-Al) alloy, I recently saw an article mentioning Ni-Zn and Ni-Sn as Raney Nickel too. #RaneyNickel...
11 June 2024 355 2 View
I have prepared Copper thin films by magnetron sputtering and the samples have been annealed at 100, 200 and 300 degree celsius. The variation of the rms roughness and all other AFM height related...
11 June 2024 9,774 1 View
What does it mean meshed wall and shell conduction with or without run-out method use to meshing copper tube in Ansys fluent?
07 June 2024 9,030 3 View
The synthesis of nickel oxide by the sol-gel method involved the utilization of specific chemical reagents. To be precise, a combination of 100 ml of distilled water, 2.49 nickel acetate, and a...
05 June 2024 761 2 View
Hi, I am experiencing a nickel leakage from my Cytiva 5mL His Trap column. I think this happened because air went inside the column due to the blockage (or clogging) of the column bed on top....
04 June 2024 3,887 0 View
spectrophotometric determination of iron and copper
04 June 2024 1,720 0 View