Is there any simulation tool suitable for a "Bufferbloat" issue?

21 February 2014 0 9K Report

Bufferbloat is a topic which has arisen recently. But a good simulation tool for "Bufferbloat" cases is not presented. The related keyword is TCP congestion control, TCP bottleneck simulation. If anybody has an idea of bufferbloat research and simulator, please share it with me.

Badges
Science topic

More Hoang-Linh To's questions See All

Which one I should choose in Abaqus ?

Hello, plese give me your idea! I simulate one slab concrete affected by temperature at top and bottom surfaces. after that, have a static load distribution with small area put on top surface. I...

12 January 2021 5,769 4 View

Analysis and implementation of Kalman filter in fixed-point arithmetic?

I would like to implement a Kalman filter for tracking applications for IoT nodes. I cannot do floating point on our nodes but only fixed point. Could you recommend some good references?

23 December 2020 4,813 3 View

Find acoustic leaky modes with Comsol?

Hi, I need to estimate the overlap between optical modes and acoustic modes of a optically guiding and acoustically antiguiding waveguide (silica core suspended in air). I setup a Comsol model...

05 November 2020 6,507 2 View

How to isolate Clostridium from mixed culture?

My Clostridium tyrobutyricum seems not producing spores. I incubated the Clostridium tyrobutyricum in 10 ml of RCM at 28 degrees Celcius for 5 days anaerobically, then heat the whole tube in 75...

25 October 2020 3,386 1 View

Protocol for purifying proteins that are stable up to 65-70C by heat treatment?

We are trying to save up on reagents and heat treatment is a promising protocol, but there are limitations with the thermostability of strand displacing DNA polymerases. Does anyone know of a...

06 October 2020 4,708 4 View

What's typical DNA yield and quality of DNeasy Powered Food Kit?

I spiked in 4-8 log CFU/ml of Lactococcus lactis into milk, and use DNeasy Powered Food Kit to extract DNA from it. Nanodrop 2000 was used to determine the values. The yield and quality are weird:...

04 October 2020 6,211 4 View

Whether analysis with CB-SEM by AMOS will have better results comparing with PLS-SEM?

With your experiences, which one will have better results, CB-SEM or PLS SEM?

15 September 2020 8,092 5 View

How can i get heparin induced coagulopathy mice? One dose IV. or multidose SC. ?

Is just one intravenous dose of heparin enough to prolong bleeding and clotting time in mice?

23 March 2020 3,688 3 View

Compare Curcuminoids analytical result between HPLC and Spectrophotometer ?

My problem now is when I analyze turmeric extracts (mostly curcuminoids) with HPLC, the results show 3 peaks of BDMC, DMC and curcumin. However, with spectrophotometer results, it just showed the...

04 March 2020 594 7 View

Should I use the long-day + low light or the short-day + normal light to slow down A. thaliana developement?

Hi everyone, I am studying leaf senescence kinetic in Arabidopsis thaliana. In the long-day condition (16h of illumination) and 100 umol s-1 m-2 light, the senescence progressed quickly. Then, I...

13 February 2020 6,626 3 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View