Why mutual inductor takes high current at no load condition?

I simulate an inductive wireless power transfer system in matlab. I set the primary and secondary mutual inductor resistance is 0.3ohm. So when i run the circuit it took high current at no load...

29 December 2020 9,536 3 View

Why both Training and Validation accuracies stop improving after some epochs?

I am using data augmentation and decaying learning rate after each epoch. If I don't use data augmentation but keeping callback, then my training accuracy reaches to 99.65% but not validation....

15 December 2020 716 10 View

GAN as Data Augmentation?

Hi, I want to apply GAN as a data-augmentation technique in my model. I am bit confused regarding implementation that how could I give the generated images of GAN to my model on run-time? because...

07 December 2020 4,703 3 View

How to improve accuracy of hard classes in multiclass classification?

Hi, I am training my models to classify 10 classes. Some of the classes are easy for my models and achieve accuracy greater than 95% but some classes have very hard patterns and accuracy stops at...

03 December 2020 324 9 View

Can I see nanoparticles using optical microscope with stage micrometer?

I am working on Solid Lipid Nanoparticles I am doing MPhil research I am preparing a formulation My topic is Preparation AND Evaluation of Indomethacin Loaded Solid Lipid Nanoparticles for...

27 October 2020 9,496 4 View

What are the laboratory analysis that can be carried out using human cadavers?

I am going to conduct a study based on the human cadaver sample analysis using various laboratory techniques. I am looking at methods that would be ideal for sample analysis and visualization to...

14 September 2020 4,805 4 View

How do we interpret the findings of variance decomposition?

I am interested in studying the variance decomposition of VAR output. However, I have a problem with how to interpret the output of variance decomposition. Therefore, I expect the anwer or...

05 September 2020 4,593 3 View

To what extant the GIS Thematic Mapping Approach is significant in the analysis?

Today, GIS is being considered the most significant and highly recommended technique in analyzing data and its also argued that in Pakistan too few people use this approach in the analysis of...

12 March 2020 5,317 5 View

How to calculate the elemental concentration in infusion and decoction?

If infusion was prepared by adding 2g of dry tea powder to 200mL boiling water (ratio of 1g per 100mL) for 10 minutes. It gives a factor of 100 for multiplication with instrumental concentration...

16 January 2020 1,844 3 View

What is your take on using EFA / CFA / CCA for measurement model analysis in SEM?

Graduate research (Ph.D.) students very often face the dilemma of whether to use EFA along with CFA (or CCA) while conducting measurement model analysis in SEM in basic business research with...

14 December 2019 5,675 11 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

No title

01 March 2021 3,905 5 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

Which group formation theory do you recommend for projects that aim to bring together entrepreneurs for training for regional development?

I would like to have ideas about which theories of group formation are suitable for entrepreneurial training projects, with the aim of creating bonds, building trust, and collaboration for...

28 February 2021 4,223 2 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

What is the most common number of epitopes in an multi-epitope Vaccine?

hi everyone, I'm interested in the field of vaccine design specifically multi-epitope cancer vaccines , I want to know if there is a minimum and maximum number of epitopes we could use in a...

27 February 2021 3,882 3 View