Can anyone give an idea about the latest research topic in Structural Engineering field ?

Can anyone give an idea about the latest research topic in Structural Engineering field ?

11 December 2018 4,458 4 View

How to give surface to surface Cohesive interaction in abaqus Explicit analysis?

how can I use Cohesive behavior, damage initiation and damage evolution??. surface based cohesion behaviour cannot supported in explict analysis?

03 April 2017 3,576 2 View

Pullout test in RCC getting an Error in Abaqus Explict analysis?

02 March 2017 9,881 2 View

How can I show crack pattern due to pullout test in abaqus?

01 February 2017 2,982 3 View

Suggest an Idea about the RC tensile crack propagation in Abaqus?

31 December 2016 7,147 4 View

How to choose a element for concrete & Rebar in Abaqus?

how to choose a element for concrete & Rebar in Abaqus?

10 November 2016 7,266 0 View

How to apply a force on nodes( in abaqus software)?

It is difficult to apply a force on nodes ? anyone give an idea...

10 November 2016 8,688 8 View

Is there any step by step procedure for FE modelling of tension stiffening Prism?

09 October 2016 9,231 0 View

Can anyone give an idea about tension stiffening effect?

1.How the tension stiffening mechanism will work ? 2. define tension stiffening ? and tension stiffening effects?

09 October 2016 5,469 1 View

Solver problem in Ansys 17.2 ?

how to resolve this problem ? (An error occurred inside the SOLVER module: general error.)

09 October 2016 9,039 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View