Is there any experimental published results of the transient behaviour of the grounding system?

12 December 2016 0 3K Report

Hi all

I'm looking for experimental results recently published of the transient behaviour of grounding system subjected to high-magnitude current (similar to lightning current).

It will be better if the grounding system is buried in multi-layer soil.

Thank you,

Omar

Badges
Science topic

More Omar Kherif's questions See All

How to embed all fonts in PDFs generated with LaTeX?

Hi All I need to submit the camera-ready paper. Since, the conference requires that the camera-ready paper should be compatible with IEEE PDF eXplore, using PDF eXpress to obtain an IEEE...

08 September 2017 3,234 1 View

How to protect the electrical installations in the aircraft in case of lack of ferroresonance or other similar?

How to protect the electrical installations in the aircraft in case of lack of ferroresonance or other similar? (fault currents of high-frequency)

04 May 2017 6,356 1 View

The critical electric field of the earth, can be considered as a calibrating parameter ?

Hi all The dynamic response of the grounding electrodes subjected to such current pulses is predominantly influenced by same physical processes, which are related to the soil ionization in the...

11 December 2016 6,181 1 View

Why the good grounding system should dissipate the lightning current into the soil as fast as possible?

Hi all Knowing that a good grounding system can dissipate the lightning current into the soil as fast as possible, thereby, reduce the potential rise and potential difference within the different...

10 November 2016 4,492 3 View

How to use Cauchy Residue Theorem in MATLAB ?

Hi All To obtain the solution of distribution current in the time domain, the Laplace transformer was performed and i have to apply the Cauchy Residue Theorem. Where this current is : ...

10 November 2016 9,828 2 View

What is the difference between the soil ionization opposite the conductivity of the soil?

Hi all Generally, the soil ionization has been found in the liquid and gas phases of the soil. For this purpose, is that this phenomenon exists for a very elevated resistivity ground where the...

10 November 2016 7,261 0 View

Expressions and relationship for the lightning frequency in frequency-dependent of soil parameter models?

It was found in some research that the frequency dependence of soil parameters is accountable for affecting the grounding potential rise of electrodes. For this purpose, many models have been...

09 October 2016 5,968 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View