Is there any evidence that DMSO by itself can act as immunogenic?

10 October 2015 1 3K Report

is there any evidence that DMSO by itself can act as immunogenic?

I believe that there's actually evidence to the contrary-- DMSO has been studied as an anti-inflammatory in the literature.

Badges
Science topic

More Zaid Al-Attar's questions See All

Hi I need 2020 6G and 2020 network coding references to cite soon in my 6G network coding paper ?

I have a paper at the last stage of publication on Q1 journal and I was asked to add 2020 references regarded 6G and network ciding

03 October 2020 5,177 3 View

How to use Tresca criterion in Abaqus VUMAT?

Hello, I know that Abaqus uses Mises yield criteria by default, and I have heard that if I want to use Tresca then I need to implement this in a VUMAT subroutine (for Abaqus/Explicit). I'm sure...

06 March 2020 2,435 3 View

Which software allows high quality schematic drawings for publications?

Hello, I have spotted a number of high quality schematic diagrams, such as the one attached here, from publications. Which software is able of reproducing such high quality schematic...

06 March 2020 4,460 3 View

Why does increasing strain hardening exponent result in less material necking?

Hello, According to the power law, Stress=K*strain^n. Could someone please explain why an increase in strain hardening exponent n results in less material necking from this equation? Please see...

15 February 2020 3,984 4 View

How do I make Abaqus stop the simulation once a critical value of PEEQ has been reached?

Hello, I am doing a series of metal forming simulations in Abaqus. I want the simulations to automatically stop when a critical value of PEEQ (or some other variable) has been reached, in order...

05 February 2020 5,114 4 View

How can I show through thickness stresses along a non-linear bending path in Abaqus?

Hello, I am doing a non-linear beam bending / forming analysis in Abaqus. I want to to get results for the stresses through the thickness direction, where the top fibre will be in tension and the...

17 January 2020 7,903 9 View

Why do I get different FE simulation results each time the solver is run?

Hello, i am performing a highly non linear metal forming simulation using PAMSTAMP FE simulation software. I have noticed that for the same mesh and boundary conditions, I get different results...

01 January 2020 1,074 4 View

What's the typical active area for anode and cathode for EIS test?

EIS, Active areas of Anode, Active area of cathode, SOFC

16 November 2018 3,137 4 View

What's the typical active area for anode and cathode for EIS test?

EIS, Active areas of Anode, Active area of cathode, SOFC

10 November 2018 8,856 5 View

Can Hedge's correction be run where I have a small sample size but repeated test (ie total output over 11 data points)?

How to run this on SPSS?

17 September 2018 2,519 1 View

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

Should we change media after1st 6hrs after plating HUVEC bought from INVITROGEN?it's not recomended by invitrogen.Will DMSO present in stock matter?

We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...

02 March 2021 3,713 2 View

Bought HUVEC from Invitrgen.need to revive it.expected it is cryofreezed in DMSO.Do I need to remove the DMSO for plating the cell for the 1st time?

After I cryofreeze the cell do I need to remove the DMSO for culturing the cell for next passages .

28 February 2021 7,738 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

How to dilute Toxin-DMSO solution?

I have a concentrated solution of a toxin(50 micromolar) in DMSO 100%. I need to dilute it inorder to dilute both the toxin and DMSO wich can be toxic to cells. Which would you guys recommend to...

19 February 2021 7,447 2 View

How to successfully revive cells stored at -80 degree C for a year?

I am working on C6 cells along with other neuronal cell lines. We have preserved the cells in 90%FBS and 10% DMSO solution. We are reviving the cells after a year and cells are either not binding...

18 February 2021 4,499 1 View

How can I make sure that BCTC doesn't fall out of solution/form DMSO crystals when treating cells?

I resuspended my BCTC as described on the bottle at 10mg/mL in DMSO. However, I can see the formation of crystals which I can only assume are DMSO and that the drug is precipitating out of...

14 February 2021 5,633 1 View

Can anyone suggest a way to dissolve insulin which is for rat/mouse injection?

We are trying to inject insulin to rat or mouse, but the insulin we've got is powder, and there are many ways for dissolve, like in saline, PBS, DMSO, or in Tris-HCl, can anyone give us a...

13 February 2021 8,426 10 View

DMSO concentration in cell culture? Precipitating while PBS is added?

I am testing a compound on RAW 264.7. the compound is soluble in DMSO. but to ensure that final concentration of dmso is not more than 0.1%, we are first dissolving it in dmso and then diluting it...

11 February 2021 1,136 3 View

What are the main conditions suited for synthesizing a PVDF thin film by solvent casting method?

I have been trying to synthesize PVDF thin film by solvent casting method. I started by using 2:3 DMSO: acetone as solvents. The solution was stirred for 3hrs at 60 deg and was dried at 90 degrees...

09 February 2021 8,850 3 View