Is there a way to export the nodal strain values of a geometry from ansys into matlab as a geometry to perform BESO topology??

13 February 2019 0 9K Report

I am trying to perform Topology optimisation using BESO, I have a matlab code which works on a simple beam however I am able to export the geometry of my shape into matlab for an analysis

Badges
Science topic

More Matthew Jones's questions See All

Anyone know of a good progesterone antibody?

I am looking for a good progesterone antibody to quantify levels of progesterone in zebrafish. Applications would be ELISA, and immunohistochemistry.

28 February 2021 5,929 2 View

Is there a suitable way to confine cell attachment area inside a multi-well plate?

Are there any types of cylindrical cell culture inserts that are designed to confine cell seeding area? Say, if I'm using a 12 well plate (3.5 cm^2/well), but only want to seed cells in the middle...

22 February 2021 7,127 4 View

Why am I getting such large heats of dilution in my Isothermal Titration Calorimetry Experiment?

I am trying to measure binding of calcium to an expressed protein we are studying and am getting very large heats of dilution for the calcium solution in my control tests. We prepared a 1 M CaCl2...

07 February 2021 7,532 1 View

Having trouble with qPCR amplification plots. My curve's never seem to reach a plateau. Any ideas?

The parameters of the curve all seem acceptable, typically reactions results are above 0.9852, -3.1 to -3.6 slope, and 90-110% reaction efficiency. The results seem to be what I would expect from...

04 February 2021 1,138 3 View

I am looking to develop a basic oral microbiome assay. Can anyone advise on culture vessel, conditions and organisms that require minimal maintenance?

I am looking to investigate oral care products with an easy-to-prepare culture of orally derrived microorganisms.

21 January 2021 3,448 1 View

Cause of blisters in ALD layer at the edge of electrode?

I've encountered a defect during processing that I can't figure out, so I'm hoping I might find some ideas here. My mask design is a microelectrode array, with 60 microelectrodes with diameter...

19 January 2021 665 1 View

Difficult to silence gene?

I have been trying to silence a gene of interest but I could not get silencing efficiencies beyond 50% My method of detection is via RT-qPCR and samples were extracted 48hrs post transfection. Are...

09 January 2021 3,404 4 View

What form of data analysis should I use for my pilot study?

I am currently conducting my final year dissertation which is looking at the efficacy of common police lineup practices. However, before I launch my study, I have put out a pilot study which is...

08 January 2021 4,376 4 View

Is it normal to use Tris buffer when testing for bacteriostatic properties of isolated compounds?

Hello, to start off I attempting to test the bacteriostatic properties of certain compounds. I bought a kit that contains some of the equipment to perform this analysis, however, in the included...

02 January 2021 2,338 2 View

Cleaning SGE Micro Channel Device?

Hello all, I have a 3-port SGE microchannel splitter in my Thermo Trace 1310 GC connected to an Isolink 2 combustion interface. My microchannel device is clogged and my flow is significantly...

29 December 2020 7,002 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View