I am looking for a some kind of simulation tool so as to reduce a large multi-bus (IEEE 13 bus node test feeder) in to ait equivalent IEEE 1547.1-2005 std .test circuit model.
I am attaching image of circuit model to which I want to reduce.
Hi Nitin, Section 4 of the following paper describes an approach for approximating a general distribution network with a two-bus equivalent network.
Article Loss Induced Maximum Power Transfer in Distribution Networks
Thanks a lot Sir
IEEE 13 bus test feeder basic book for development in SIMULINK
08 September 2019 8,713 1 View
Occurrence of an unintentional island in a DG interfaced power system network is due to many reasons and one of the reasons is occurrence of a fault. There is sometimes confusion so as to how a...
31 December 2018 9,435 2 View
I mean if the paper is written in MS word for a journal then will it impact negatively for chances of acceptance. I know this question sounds silly but as I am beginner so I am not clear about...
02 March 2018 5,712 4 View
Occurrence of generation-load match for grid-connected PV systems especially when penetration level is high due to the variation of solar insolation level
01 February 2018 5,578 2 View
Control loop design for Passive Islanding Detection Methods in PSCAD software: Over/under Voltage and Over/Under frequency Voltage Phase jump Harmonic detection
31 December 2017 1,163 3 View
I mean suppose you are developing say for example an IEEE 34 bus system in Matlab Simulink software and obtain the results of fault analysis for example. Then what is the need to go for real-time...
10 November 2017 1,128 3 View
How to trap heat from the resistances of power transmission lines?
03 April 2013 3,607 0 View
Heat trapping device from rheostats
10 November 2012 4,761 6 View
I want to trap the heat from the normal rheostat (laboratory type) and utilize it whenever required , I know that the amount of heat dissipated is very less but still it can be used to produce...
10 November 2011 4,857 0 View
PLL based synchronization
01 January 1970 404 0 View
After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...
05 August 2024 9,637 2 View
Hi everyone I need a file with a dirty and clean potato image
04 August 2024 7,199 4 View
Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...
03 August 2024 3,371 3 View
I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?
02 August 2024 3,143 4 View
I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.
02 August 2024 6,789 4 View
Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out? For example consider a process for certain product manufacture where a new process flow...
31 July 2024 781 1 View
What can you look for to know that the circuit model being used is overfitting the data. How do you know when overfitting is occurring?
31 July 2024 7,425 0 View
Dear researchers. I tried using the IHC PROFILER in image j to quantify nuclear DAB staining. I followed the instructions in the original article by "Varghese F, Bukhari AB, Malhotra R, De A...
29 July 2024 2,229 0 View
My question pertaining to the DAB staining in cytoplasm of human oral squamous cell carcinoma tissue. When quantifying the epithelial cancer cells do we have to crop remove the stromal tissue?...
29 July 2024 2,682 6 View
Dear All Gromacs User I would like to restart MD without using checkpint .cpt files? I heard there is a way for acheiveing this. Any input and sugegstions are most welcome. Thanking You Budheswar
29 July 2024 3,084 8 View