Can any one suggest me a standard textbook to develop IEEE node test feeder for 50hz system in MATLAB SIMULINK?

IEEE 13 bus test feeder basic book for development in SIMULINK

08 September 2019 8,641 1 View

Is there a simulation tool to reduce large multi-bus (say IEEE) network in to a 2-bus network?

I am looking for a some kind of simulation tool so as to reduce a large multi-bus (IEEE 13 bus node test feeder) in to ait equivalent IEEE 1547.1-2005 std .test circuit model. I am attaching...

31 December 2018 3,733 2 View

How to categorize fault event as an islanding (or) non-islanding event?

Occurrence of an unintentional island in a DG interfaced power system network is due to many reasons and one of the reasons is occurrence of a fault. There is sometimes confusion so as to how a...

31 December 2018 9,351 2 View

Does writing a reputed(SCI) journal paper in LATEX software impact positively the chances of acceptance?

I mean if the paper is written in MS word for a journal then will it impact negatively for chances of acceptance. I know this question sounds silly but as I am beginner so I am not clear about...

02 March 2018 5,642 4 View

How does the variation of solar insolation level effects the possibility of occurence of an unintentional island?

Occurrence of generation-load match for grid-connected PV systems especially when penetration level is high due to the variation of solar insolation level

01 February 2018 5,513 2 View

Suggest me few articles on anti-islanding protection control loop design for solar PV inverters in PSCAD?

Control loop design for Passive Islanding Detection Methods in PSCAD software: Over/under Voltage and Over/Under frequency Voltage Phase jump Harmonic detection

31 December 2017 1,091 3 View

Can any one here tell me the need for real-time simulation platforms like RTDS/Typoon HIL for simulating Power System bus network?

I mean suppose you are developing say for example an IEEE 34 bus system in Matlab Simulink software and obtain the results of fault analysis for example. Then what is the need to go for real-time...

10 November 2017 1,061 3 View

Heat trapping

How to trap heat from the resistances of power transmission lines?

03 April 2013 3,531 0 View

How to trap heat dissipated from a rheostat?

Heat trapping device from rheostats

10 November 2012 4,701 6 View

How do I synchronize a voltage source inverter with grid in MATLAB SIMULINK?

PLL based synchronization

01 January 1970 339 0 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View