How to trap heat from the resistances of power transmission lines?
IEEE 13 bus test feeder basic book for development in SIMULINK
08 September 2019 8,641 1 View
I am looking for a some kind of simulation tool so as to reduce a large multi-bus (IEEE 13 bus node test feeder) in to ait equivalent IEEE 1547.1-2005 std .test circuit model. I am attaching...
31 December 2018 3,733 2 View
Occurrence of an unintentional island in a DG interfaced power system network is due to many reasons and one of the reasons is occurrence of a fault. There is sometimes confusion so as to how a...
31 December 2018 9,351 2 View
I mean if the paper is written in MS word for a journal then will it impact negatively for chances of acceptance. I know this question sounds silly but as I am beginner so I am not clear about...
02 March 2018 5,642 4 View
Occurrence of generation-load match for grid-connected PV systems especially when penetration level is high due to the variation of solar insolation level
01 February 2018 5,513 2 View
Control loop design for Passive Islanding Detection Methods in PSCAD software: Over/under Voltage and Over/Under frequency Voltage Phase jump Harmonic detection
31 December 2017 1,091 3 View
I mean suppose you are developing say for example an IEEE 34 bus system in Matlab Simulink software and obtain the results of fault analysis for example. Then what is the need to go for real-time...
10 November 2017 1,061 3 View
Heat trapping device from rheostats
10 November 2012 4,701 6 View
I want to trap the heat from the normal rheostat (laboratory type) and utilize it whenever required , I know that the amount of heat dissipated is very less but still it can be used to produce...
10 November 2011 4,780 0 View
PLL based synchronization
01 January 1970 339 0 View
Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...
01 March 2021 7,168 9 View
Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?
01 March 2021 9,785 3 View
I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...
01 March 2021 6,450 5 View
I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...
28 February 2021 8,626 3 View
Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...
26 February 2021 6,253 3 View
Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...
25 February 2021 1,675 3 View
I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium
24 February 2021 1,915 1 View
I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...
23 February 2021 6,043 1 View
Hi I am working recently on a project where I have to study how the thermal properties or heat transfer enhancement of nanofluids as the volume fraction changes, or if a magnetic field is applied...
22 February 2021 961 2 View
Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....
22 February 2021 9,972 4 View
