Is the validation required for the experimental models?

More Alaaeldin Magdy Ogail's questions See All

How to differentiate between asthma and COVID-19 symptoms ?

People with asthma may worry whether their asthma may put them at risk for getting coronavirus (COVID-19). It can be confusing because both asthma and coronavirus share symptoms of cough and...

29 December 2020 6,987 6 View

Are the Physiological and phytochemical studies of grafted cucumber on several rootstock changed or not ?

I have my Ph D student work on project: Physiological and phytochemical studies of grafted cucumber on several rootstock ? here were checked the following: Plant vegetative growth behavior The...

06 May 2017 2,599 8 View

Are the Physiological and phytochemical studies of grafted cucumber on several rootstock changed or not ?

I have my Ph D student work on project: Physiological and phytochemical studies of grafted cucumber on several rootstock ? here were checked the following: Plant vegetative growth behavior The...

06 May 2017 1,295 6 View

Can any one suggest to me anew point to work in optimal size of hybrid power system (PV, wind, battery, FC, electrolyzer, Diesel)?

I want to do a research in optimal sizing in hybrid power system, I want someone to suggest me anew point to do??

28 February 2017 3,788 8 View

What is the mechanism of fatigue induced by allergy?

One of the most miserable symptoms of allergy is fatigue. Do allergens disturb electrolytes?

25 February 2017 3,050 11 View

How can I write a result of two-way ANOVA from SPSS analysis?

I am writing these results for my P.hD. thesis, but the part of two-way ANOVA was a little bit difficult for me. so please anyone can give help? Thanks

13 February 2017 1,411 7 View

How can I model High Performance Fiber Reinforced Concrete in ANSYS 15 ?

I need Papers and previous work that may help in modeling High Performance Reinforced Concrete with Polypropylene fibers in ANSYS 15 Software

19 September 2015 3,960 2 View

Is anyone aware of a program for Smart Home Design?

Is there any program for smart Home design.

08 April 2015 4,583 5 View

I need a MATLAB Simulink model of cigre benchmark HVDC system?

Thanks in advance for your replies.

18 March 2015 190 3 View

Could you recommend any companies that produce precise gas mixes with mass flow controllers (MFC) for gas sensing applications?

Thanks in advance.

12 October 2014 2,615 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Are there any instruments for studying time similar to the way it is in space?

There are a huge number of methods for studying objects in space, according to the senses (and not only). Mechanical, thermal, optical, acoustic, electrical, magnetic, based on particle beams,...

06 August 2024 7,102 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

How to report results of Generalised Linear Mixed Models in a journal article?

Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...

04 August 2024 4,130 4 View