Is the suction pressure of a pump, the static pressure, dynamic pressure , hydrostatic pressure or total pressure at the inlet of pump?

05 May 2017 0 2K Report

Suction pressure = suction surface pressure + static suction pressure - suction friction pressure

Badges
Science topic

Similar topics
Thermodynamics
Pressure

More Loo Kian Sing's questions See All

Is the velocity of the fluid is controlled by valve?

Pump will create differential pressure when it starts to operate and drive the fluid to the discharge, but the velocity of the fluid is still controlled by valve. Is this correct?

08 September 2017 9,392 10 View

What is the percentage range of the capacity that can be spilled back?

Kindly refer to the image uploaded. May I know, what is the percentage range of the capacity that can be spilled back to the suction of the pump through the recirculate line (restrict orifice...

06 July 2017 2,942 2 View

Is there any difference between pressure gauge and total fluid pressure at a particular pipeline location?

If yes, is the pressure used in the calculation of the pressure drop of suction pressure of a pump, the gauge pressure at that location or the total pressure of the fluid? Beside, if the pipeline...

04 May 2017 1,837 6 View

Is there any pressure drop across an expander for any fluid?

By referring to the "Fluid Mechanics Fundamentals and Applications" by Yunus A. Cengel and John M. Cimbala around page 353, I notice the pressure will increase after expander.Or can I use the...

04 May 2017 7,937 4 View

Can a capacitance type transmitter to be intrinsically safe type also?

If no, what is the difference between capacitance type transmitter and intrinsically safety type transmitter?

04 May 2017 7,324 2 View

Is there any water formed in a closed loop system (closed loop tube) with fluid, refrigerant?

I have seen the filter dryer is used in the cooling system for refrigerant part in between the condenser and expansion valve. Is there any water formed inside the tube when there is cooling process?

03 April 2017 1,344 5 View

What is the formula to calculate the longitudinal stress due to weight (No liquid) of vertical pressure vessel?

I am using the formula, S= Wv/ (PI*D*t), but still unable to get the exact answer as calculated by PV Elite.

09 October 2016 8,125 3 View

How to make corrosion inhibitor from raw materials with known concentration?

The corrosion inhibitor is used to reduce the corrosion rate of a material.

31 December 2015 3,000 7 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

Z-average size from Dynamic Light scattering can it be lower than the original probe size?

Hi everyone, Recently I have been conducting Dynamic Light scattering experiments in a micellar solution at 5 and gel at 37 degrees of Celsius with latex particles of diameter 190-500 nm. While...

01 August 2024 1,168 4 View

I found the zeta potential of exosomes in DLS and it was -8mv. So is it correct or not ?

What should be the zeta potential of bovine milk exosomes

25 July 2024 7,376 5 View

Comparing Liposome Size: DLS Measurement vs. SEM Observation with Air Drying ?

I have an issue with SEM imaging of liposomes. When measured by DLS, they appear to be around 120 nm, but when using SEM with simple air drying, they appear much larger, around one micrometer.

25 July 2024 3,395 3 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

Franklin M. Fisher (1983) Disequilibrium Foundations of Equilibrium Economics. How is it estimated now? How is it related SMD results?

Fisher studied if there is an out-of-equilibrium process that rapidly converges to some equilibrium points. He claims that Hahn process has a Lyapounof function and therefore convergent to an...

15 July 2024 1,460 4 View