Is that possible to make a "for loop" with the different boundary conditions via the PyFluent interface?

01 September 2023 0 570 Report

I would like to ask that, is that possible to make a for loop with the different boundary conditions via the PyFluent interface? In addition, is that possible to analyse different sized geometries? For example 2 different diameters for a pipe geometry. Can we import 2 different geometry and mesh with the PyFluent script?

Badges
Science topic

More Selim Can Bozkir's questions See All

About forging of Mo Alloys ?

Hello dear Academicians, I am working on the forging of Mo alloys, but I wanted to consult you on an issue I could not solve. Mo is easily oxidized during forging and MoO3 is formed. Is it...

09 February 2021 1,989 3 View

Molydenum Alloys Forging Process ?

Hello dear Academicians, I've been struggling on a specific subject for a while. Hence, I'd like to get some advice. I am working on Mo-0.5 Ti alloy production via powder metallurgy technic. I...

20 December 2020 3,805 2 View

How to distribute Titanium in Molybdenum host material via PM?

Hello dear Researchers, I've been working on to produce Mo-Ti alloys via powder metallurgy method. Yet, I've come across a problem: I can not properly distribute Titanium in Molybdenum host. I'm...

10 August 2020 4,502 3 View

How to distribute Titanium in Molybdenum host material via PM?

Hello dear Researchers, I've been working on to produce Mo-Ti alloys via powder metallurgy method. Yet, I've come across a problem: I can not properly distribute Titanium in Molybdenum host. I'm...

10 August 2020 5,909 4 View

How to peel off PDMS film from a glass petri dish without damaging it ??

I have prepared 15wt.% PDMS and poured it on a glass petri dish, then let it dry for 72 hr at room temp. after I tried to peel it and it doesn't work, so I am crosslinked in an oven for 3 hr , but...

26 July 2020 9,892 2 View

What is the best solvent for PVDF ?? Dimethyl sulphoxide or Dimethylacetamide??

For membrane preparation PVDF will be used , and I was wondering which solvent is the best for dissolving it, non-Toxic solvent , useful in dissolving other polymers such as PES, PDMS, Peba

05 July 2020 1,655 5 View

Are there any good data-sets or research papers/code for Deep Learning Model for medical 3D Construction from 2D CT Images?

I want to create a Deep Learning Model for 3D Construction of Breast Cancer in CT Images. However, I cannot find an appropriate data-set or research paper. The data-set should be multiple CT scans...

04 March 2020 3,614 3 View

I need a conference paper published in a conference book in 1998. Can anybody help me in getting this conference paper?

High Fidelity Mathematical Modeling of Reaction Wheel Performance (AAS 98-063) Bialke, B. /Guidance and Control 1998. (Advances in the Astronautical Sciences )

26 January 2020 813 2 View

Which type and size of beads are the most suitable for homogenizing the large intestine of rats?

There are too many information about this topic presented below: 2.4 mm Metal (Steel) Beads are recommended for hard tissues, skin, muscle, bone, hair 2.8 mm Ceramic Beads are recommended for...

15 November 2019 3,799 3 View

Can you help me with the conversion of the given bond diagram to block diagram ?

Does anyone have any clue or idea about drawing block diagram of this bond graph ? This problem is very important for me so any little help is appreciated. Thanks.

10 June 2019 4,427 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View