Is micro analysis of infilled RC frame possible in SAP2000?

More Chandani Chandra Neupane's questions See All

Given, ER = 0.2, WHAT WILL BE THE AIR FLOW RATE IN kg/hr?

I have a biomass with given ultimate and proximate analysis data. I am using Aspen plus for the simulation of gasification of biomass. In experimental data the gasifying agent air flow rate is...

18 June 2024 2,743 1 View

How can i solve this error in ASPEN PLUS?

i am doing a project on gasification. during pyrolysis i got the following error: * WARNING COMPONENT 'BIOMASS' IN SUBSTREAM 'NC' HAS ZERO FLOWRATE IN THE OUTLET STREAM. FRACTIONAL...

18 March 2024 6,025 1 View

Any localization sequence to target cell organelles?

I am looking for the paper or the persons who worked on cloning of short sequences targeting the different cellular organelles (vacuole, mitochondria, plasma membrane, septum) in plant pathogenic...

11 March 2024 1,878 0 View

How can i solve this error in ASPEN PLUS: COMPONENT 'DRY-BIOM' IN SUBSTREAM 'NC' HAS ZERO FLOWRATE IN THE OUTLET STREAM. FRACTIONAL CONVERSION ?

Dear all, I am doing a gasification of biomass. In the pyrolysis section i have used RSTOIC for the devolatization of the biomass. i have specified the yield from the RSTOIC. it gave me the...

19 February 2024 8,026 0 View

What is the difference between Mixed Methods and Triangulation Methods?

12 February 2024 9,962 3 View

How is HPLC method qualification perform?

I am working in validation and qualification of new HPLC method. Your insights and feedback are greatly appreciated.

02 December 2023 8,514 4 View

Can we say there is mediation in this case?

While testing the mediation via Process Macro in SPSS, I obtained that my Total Effect is significant, Direct Effect is also significant, but My Indirect effect is not significant. In this case,...

23 September 2023 6,641 1 View

What I have to write in review of literature and discussion part of my dissertation ?

Hello, i am going to write my dissertation and i am confused in review of literature and discussion part. Please tell me what is the difference in between them.

04 September 2023 4,969 4 View

How to do Mode analysis of two coupled silicon waveguide properly for the calculation of effective index?

Hi, I wanted to do mode analysis of two coupled silicon waveguide separated with 200 nm with the dimension of 400 nm and thickness 0.215 nm. What should be the height and width of cladding? I...

28 June 2023 7,646 3 View

RMSD error in PyMol ?

Please provide some insights on it. When calculating Rmsd from PyMol it shows "atomic alignment failed (mismatched identifiers?)". How to solve this?

20 June 2023 1,016 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

In SEM, if a latent variable consists of three observed variables, and each observed variable has four items, what should I do?

Suppose I am studying the construct of "Academic Motivation" (latent variable) in students, which is measured through three observed variables: "Intrinsic Motivation," "Extrinsic Motivation," and...

31 July 2024 3,913 6 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

Dr. Amit Srivastava

read the software manual carefully.

Vaibhav Singhal

You can refer to the research paper: Goutam Mondal and Sudhir K. Jain (2008) Lateral Stiffness of Masonry Infilled Reinforced Concrete (RC) Frames with Central Opening. Earthquake Spectra: August 2008, Vol. 24, No. 3, pp. 701-723.