Are these machines available commercially or still in the development stage under R&D?
Respected Sir, As we know, the ceramics are brittle in nature, if we add polymer and ceramics in piezo ceramics, then the material behaves as flexible. What is the main reason behind it? Kindly...
01 February 2019 2,263 4 View
Dear Sir, kindly give your valuable suggestion for the mandatory instruments requirements for the Essential Oil Testing laboratory
11 December 2018 5,978 2 View
Respected Sir, if we have the steam distilled essential oil and we would like to extract the abosutes from it, what should be the exact method of extraction and what are the various factors that...
11 December 2018 3,771 3 View
Kindly give some suggestions and references related to it.
10 November 2018 6,980 3 View
Respected Sir, If we are cleaning the boiler tubes and shell by boiling out method, which one chemical or acid is best suitable? What quantity of acid should be mixed with water solution for...
10 November 2018 6,567 0 View
As we know the GCMS (Gas Chromatography Mass Spectoscopy) is genrally used, but i am interested to know the latest techniques to measure the chemical constituents of natural products and essential...
10 November 2018 873 4 View
Respected Sir, If someone has PDF version of the above mentioned book. Kindly forward it.
08 September 2018 6,341 0 View
This question is related to ANFIS modeling. Kindly give your suggestions.
05 June 2018 1,534 8 View
on what basis the no. of epochs are selected? is there any influence of no. of epochs on output results? kindly give your suggestions.
05 June 2018 9,766 3 View
What are the various controllable parameters? Standard Procedure to produce the Al-Li alloys for industrial application. Kindly suggest me some references related to the processing of AL-Li alloy.
05 June 2018 7,255 2 View
I am trying to drop cast 2D Materials on Glassy Carbon Electrode for Cyclic voltametry and EIS purpose. What would be best binders to use?
23 July 2024 5,776 2 View
I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...
26 June 2024 2,358 0 View
What is the difference between absorption and adsorption?
30 May 2024 4,447 27 View
I would like to calculate the gear wheel and gear tooth deformation due to rotational speed? The gear shaft is mounted on hydrodynamic bearings. What are the boundary conditions need to apply?...
21 May 2024 8,067 0 View
What is the difference between reaction and interaction in chemistry? Would you please provide me with the details?
13 May 2024 2,524 6 View
Electrochemistry is a pathway to convert CO2 into valuable products such as CO. However, a potential side product in the cathode is H2. I wonder if it is possible to tune the composition of the...
12 May 2024 9,061 3 View
After running chronoamperometry and quantifying the products using anal techniques
12 May 2024 9,061 0 View
I would like to understand how we can apply electrochemistry in minimizing pollution and waste
06 May 2024 7,132 2 View
Hi researchers. I have deposited a polymer, PANI on Glassy carbon electrode by electrodeposition method. CV results of It showing only the oxidation peak taken in 100mM ferri+ferro solution in...
06 May 2024 9,827 3 View
In some electrochemistry research papers, the result obtained from a differential pulse voltammetry (DPV) technique is presented in peak current vs. log(concentration) plot. in such cases, how to...
04 May 2024 9,605 2 View