Is it possible to have grains in the range of 50-80 micron in 6061 and 6063 alloy ?

More Py De's questions See All

RNA later for the preservation of RNA in fecal samples at room temperature for one day (37°C)?

I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...

06 August 2024 1,367 3 View

How to develop an academic literacy program for engineering at the higher education level?

Information literacy in higher education integration with curricula engineering

04 August 2024 5,368 3 View

How can i generate a CRISPR knockin mutation zebrafish model with a reporter?

Hey! I aim to generate a transgenic knockin zebrafish line that mimetizes a genetic condtition that leads to a certain disease on human. To do so, I need to insert a codon for mutagenic aminoacid...

14 July 2024 6,240 0 View

What should be the best Lumens range for T8 (120cm) full spectrum LED lamp tubes?

Please (for Arabidopsis), what could be a good Lumens and color range (Kelvin) range for full spectrum LED lamp tubes size T8 (120cm) for each shelve measuring 130x50 cm (length x width) and 60 cm...

11 July 2024 6,078 1 View

Cross Attention in Transformers: Standard applications of the same ?

What are the standard applications of Cross Attention in Transformer Architectures ?

09 July 2024 9,310 2 View

Time Series Analysis: Has Recurrent Neural Networks (RNN) ever been used on Time Series Analysis ?

Are there standard RNN architectures been applied for Time Series Analysis, forecasting and anomaly detection problems ?

30 June 2024 3,169 8 View

LSTM on Time Series: Has LSTM architectures ever been applied to Time-Series Forecasting ?

Have we ever used LSTM architectures on Time-Series Forecasting and Analysis, and gotten a decent result ?

30 June 2024 6,924 3 View

What could be causing these smears in my PCR electrophoresis gel?

I am new to running PCR gels. I loaded this gel and I thought it was fine, meaning I saw/felt no apparent punctures or spillovers to neighboring wells (see picture 1). When the gel started to run,...

30 June 2024 4,107 4 View

What are the typical applications of Large Vision Models (LVMs) ?

Where are large vision models typically used ?

25 June 2024 4,113 0 View

Are there standard libraries/frameworks for doing RLHF for training LLMs ?

When it comes to Re-inforcement Learning with Human Feedback, are there standard libraries/frameworks for training LLMs ?

25 June 2024 1,121 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How to select temperatures for two-step aging treatment in high entropy superalloys?

Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...

13 July 2024 2,417 1 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View

How to calculate the proportions in grams or milliliters of the compounds for 60 mL of SAPO-11 zeolite precursor gel?

It is required to make a precursor gel for a SAPO-11 Zeolite, the compounds are the following: * As a source of Al: Aluminum Isopropoxide (98%) Formula: C9 H21 O3 Al PM: 204.24 g/mol Density:...

01 July 2024 617 3 View

How to decide mass scaling in ABAQUS?

I am doing orthogonal cutting of aluminum. My forces are changing according to mass scaling. How to decide the scaling factor?

01 July 2024 3,749 0 View

How to solve the problem that the film obtained by magnetron sputtering on the ternary alloy target A2BC is ABC (not A2BC)?

Using magnetron sputtering with an alloy target composed of A:B:C in a 2:1:1 ratio, the resulting thin film composition is A:B:C=1:1:1. How can you achieve a A:B:C=2:1:1 composition? What are some...

24 June 2024 1,605 0 View

Joo Choi

Dr. Pallavi,

Hello,

I have studied some research fields on steel making process and continuous casting.

Frankly I don't know what is TiBAl (5:1).

Would you please make sure who is an author of articles that you are interested.

Thank you for your question and see you again.

Abdulaziz Albannai

Dear Dr. Py De could you please clarify the process.

You can check the attached paper, it may help you with AA6061